Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Greetings....
Since logging is removed from Mesh, I find it is very hard to debug the system. I wonder if it is possible to ask for your help to have a new monitor type...
SDK v15.2.0 using code from the peripheral spi example. Linux Ubuntu 19.04, uploading to nRF52 DK.
When I call my get_bma253_accel_data in main, I get a continuous stream...
The development of the custom hardware of an nRF52832 utilizing the u8g2 library has been shown to control a small display 64x48 SSD1306 driver. The prototype hardware another...
I have been migrating a project from SDK 14.2 to SDK 15.3 and have encountered an issue with UART. I am using the legacy layer with the following configurations:
I am...
Hello,
I'm evaluating nRF52811 as a long-range IC in a beaconing application.
Here's our specifications:
- The beacon must operate with Coded PHY
- The application...
Hi everyone, I know that the theoretical limit for the Bluetooth Low Energy throughput is 1 Mbit/sec, but I heard that on practice you get much lower. So I would like to find...
We were running BLE DFU bootloader for nrf52832 based on sdk 14.2; this worked fine.
We have now moved to sdk15.3 and nrf52840 as we needed USB.Our applicaton is up and...
Hello,
I have a custom nrf9160 device which requires
device stops at:
'Secure Boot: prepare to jump to Non-Secure image'
if I use this the following prj.conf:
...
Hello,
i I’m have a custom nrf9160 board. I have been using SES with j-link edu to upload firmware to my board with no issues.
Now I need to update modem firmware...
I'm trying to update my NRF52832 running s332 v5.0.0 and a stock SDK14.0 bootloader to S332 v6.1.1 with an SDK 15.3 bootloader.
I am including the flags --sd-req and --sd...
Hi All,
I am working on an NRF application that communicates with a specific mobile app, sends some measured data. Everything works fine except on some older (at least it...
Hi.
I wonder which pins are AIN0, AIN1, AIN5 AND AIN7 (on nRF52810 QFN32) ?
It seems the datasheet would tell...
I need this for a project at work.
Please. And Thank...
Hi,
I am trying to debug on nRF52840 dongle using JLink debugger and Keil uVision V5.18.0
What I have been through is here: https://devzone.nordicsemi.com/f/nordic-q-a...
Hello,
Greetings!!!
I am working on nRF52832 having SDK 15.3.0, Windows 7 and Segger Studio IDE.
Right now I am implement OTA in my custom application.
I upload bootloader...
Hello
The latest nRF_Connect_SDK documentation define an not available version of Segger JLINK. https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/doc/release...
