Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I've been recently working on trying to stablish an i2c (twi) communication between my nrf52 Dev kit and a LIS3DH located in a STEVAL-IDI-003V2 board.
In this post https...
Hi!
I have used NRF52832 on PCA10040.
I want use several pair (master and slave) in one room.
For this I try to select a different frequency for each pair.
But, when I...
When trying to use BPA600 BLE analyzer I was not able to see the LL packets. when contacted Frontline/Teledyne tech support they said I am into BLE 5.0 stack.
However so...
Hi ,
I configured nordic as slave and it looks like the transactions been successful, but when 2 SPI transactions occurs consecutively slave was setting 0xAA in return...
Hello, we are developing using nRF52840 DK, SDK version 15.2 and Mesh SDK version 3.1.0, using Segger Embedded Studio.
Currently we are using the nRF Mesh app to provision...
Dear support team,
I wanted to program and debug nrf52840 dongle through an external debugger. For that, I connected the debug out of nrf52840 development kit to the SWD...
Hi, I recently added the buttonless DFU bootloader on my device with the debug config. I am using and I can flash an application when in DFU. Although, I cannot debug my application...
Using the Mesh SDK 3.1.0 the advertising bearer's transmission interval is limited 20msec (B EARER_ADV_INT_MIN_MS).
The Mesh Profile Spec indicates in s4.2.19 that the transmission...
Is it possible to transfer 258 bytes over the TWI interface of the nRF52832 in one transaction ? The manual says that RXD.MAXCNT is 8 bit wide only. I need to read 258 bytes...
Hello,
I need help with my project. I am adding fds library to the light sw example.
I did this steps:
1. Included necessary *.h files
2. Added fds.c to the project...
Hi, I'm using nRF52840,
I created my app, then i tryed to program with bootloader using nrfutil.
I used dfu bootloader and i created a zip.
So i could flash bootloader...
Hi, every developers,
I am testing the example of ble_app_hrs_c and ble_app_hrs using 2 nRF52840 (in SDK 15.3.0 VERSION).
My goal is that data communication with two DK...
SDK : Mesh 2.1.1
IDE : SES
I have a node.
After this node provisioned the mesh network,I change this node model publish address by local.
then I restart this node...
On the UART and I2C operations, are the input/output pins configured using CMOS or TTL logic levels? I am trying to design a test to test signal integrity and there are some...
Hello, I am a new bee in using nRF52840. I have looked into the given example in SDK called usbd_hid_composite ( infocenter.nordicsemi.com/index.jsp . It worked well in my...
