But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I am developing software for the nRF52. As recommended by many recent posts here in the Developer Zone, I have upgraded to SDK 11. I am working on an application for a battery...
Hi, I would like to share some valuable information regarding the BLE DFU (secure bootloader) and a MESH application which uses persistent storage for provisioning data. I...
Dear all,
I'm using two nRF52 Preview DK boards with the SoC nRF52832 and I'am testing the light switch example with sdk 3.1.0.
For my application I need one client...
MY CHIP is NRF52840, EVB is PCA10056
SDK: nRF5_SDK_15.0.0_a53641a
bootloader use secure DFU example: \nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10056_ble...
Hi,
I found your PDM Working Example. However I wonder what to make of the data I get.
What is the CONFIG_PDM_BUFFER_SIZE_SAMPLES for? Do I get 16Bit Bit-Schemes from...
I am using SDK12.3.0 + SoftDevice S130 in nRF51 DK.
I create 4 channel PWM (+ppi) in timer1 & timer2, because I know timer0 is used by Softdevice, RTC1 by App_timer.
My...
This is more of a Segger question than an Nordic question, but it seems enough folks here use J-Link tools that I could ask here.
RTT Logger and RTT Viewer doesn't log the...
Hi Nordic community
I want only send data using ble app_uart example with out receiving anything. So i tried to send the data that i received from my device to my android...
I am working on the safety-critical system, I have, ON and OFF function, the entire system using UART communication. In which I am using the nrf_queue() and push the data...
Hello everyone,
I have been using nRF52832 module from Raytac ( link ) for my circuit and I got a trouble with sending advertising packages to other master devices. I installed...
Hi,
I am trying to merge working code that places the microcontroller in system_off when a switch connected to pin 16 is opened. It then wakes up the micro controller when...
Hi, I am working on application where I need to store some bigger files. I chose to use sdcard, but I get weird behaviour. Some sd cards, this looks like totaly random ones...
Hello,
I am playing around with the Blinky example on my custom board, where I have one button and two leds. Everything works fine and I can control the LED2 and detect...
I am using the nRF52832 chip with an SDI connected microSD device. I am able to communicate with the microSD card formatted as FAT32, store data, read data all with the FATFS...
