Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Im developing a BLE beacon based on the eddystone example provided for the NRF52832. I've found that in softdevice applications, the radio frequency can not be changed directily...
I am developing a custom board using nRF52810.
SoftDevice S112 6.0.0 and SDK 15.0.0 are in use.
I want to know the maximum current in Idle state .
Current measurements...
Hi all,
I am currently trying turning off the active time, so that the nrf9160 immediately goes in power save mode after RRC Connected Release.
If I send the command ...
I connect VBUS to VDDH, and use a USB cable for power supply(high voltage mode), but I cannot download firmware into the 52840.
Unless I power the 52840 from the VDD pin...
Hello,
I'm a teacher. I use the microbit card that loads one of your components. Nordic nRF51822-QFAA-R rev 3 Could you tell me if this processor is based on a Von Neumann...
Hello, just a few quick short questions regarding nrf52 devices:
Do I have to configure and initialize them before using?
Which function should I use? I...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Issue-background...
Hello,
nRF52840-DK
SDK 15.3.0
SoftDevice: s140
IDE: SES
Example: Flash_fstorage_s140_pca10056
I do not read back the expected value in the example. The terminal...
Hi, I am trying to do DFU OTA. I am using SDK v16.0, s140_nrf52_7.0.1_softdevice.hex, SES and nRF52840 dev kit. I am finished with my application and it functions as expected...
Hi,
We are a module manufacturer. We are making modules based on WLCSP, QFN based nRF52840 SoC.
Can you please provide software(preferably GUI) available for module FCC...
Hi guys, i can't figure out how to create an event handler in my Mesh Client.
The functionality of this handler should be to set a flag on the 'NRF_MESH_EVT_TX_COMPLETE...
I used keil v4 compile the following project F:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral\ble_app_uart\pca10040\s112\arm4\_build get file nrf52832_xxaa.hex of size 101kb...
