But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi Nordic team,
I have 2 nRF52840 DK boards.
I followed the steps mentioned in the below link, I am able to Transfer the DFU archive over serial with nrfutil(LED keeps...
I want to enable the Logger Module to have the high default severity of Error and then be able to enable lower level severities on an individual module for debugging. Is this...
Hardware used: 2 nRF52480 DK boards
I am running nRF5_SDK_15.0.0_a53641a\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput example, I want to increase...
I read zephyr official document of nrf52810 support：
http://docs.zephyrproject.org/boards/arm/nrf52810_pca10040/doc/nrf52810_pca10040.html
It describes like this : ...
Hello,
I just got my nRF52832 DK and am following the Getting Started at the Infocenter to get familiar with it. Running Ubuntu 16.04 and all the latest Nordic tools (SDK...
Greetings, I got a nRF52832 DK and only just found out that Smart Remote 3 is probably more what I'm looking for. It should be no problem to set it up on the DK with an appropriate...
I am working on a custom board based on nrf52810 that my client provided. In this board the accelerometer (Bosch BMA250E) power has been controlled by the PIN 9. However when...
Hi, everyone
I have some problems to make the Image Transfer Demo APP work
I have read the content of the website( https://github.com/NordicPlayground/nrf52-ble-image...
Hi,
I have 2 devices: one nrf52832 and one nrf52840 dongle. After enabling PHY feature (see the following code) in nrf52832, I tried to connect it using the dongle in the...
Hi,
I got the following hardfault when running sdk 14.2, nrf52832. Since the address shows it locates in softdevice...I do not know why. May you please give me tip? Thanks...
Hello, we have a handheld device with Microchip (ex. Atmega) Microcontroller that essentially monitors and records different environmental conditions and stores them them...
I am making PUC for sending & receiving string through ble nrf51822 to phone(nordic app) with particular user define time interval like 1 min , 5 min etc. using ble_app_uart...
I'm running \nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs and following instructions from http://infocenter.nordicsemi.com/index...
Hello,
We are using in nrf51822 in a product.
I do not understand whether by definition and, thus, always, before connecting, whether a peripheral
goes to sleep between...
