Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi All,
SDK => v17.1.0
IDE => Segger
Project => ble_app_bps
I use LightBlue to connect my board,and going down to the device information service I choose system...
Hi,
I'm using nRF5340 DK, one board is programmed as central and 2 boards are programmed as peripherals. When I flash the central program it is selecting a random board...
Hello,
we are currently experiencing issues with the SPI interface which we suspect is due to the behaviour of the MOSI line in idle state. We have noticed that during communication...
Hello,
I am planning to test ethernet module on nRF9160, use SEGGER SDK v1.7.0 for compile the programs. In Q&A I saw using can bus module & ENC424J600 ethernet controller...
Hey,
I try to read the CRC from E-Paper display series 1.02 inch (GDEW0102L4f) with no success (I'm working with nRF52833 Development Kit)
My code and the official Goodisplay...
Hi
I can‘t find the bank size configuration in the project secure_bootloader_uart_mbr_pca10056。 For safety reasons, I want to artificially divide the size of bank0 and bank1...
Sir,
I am using a U-BLOX NINA B302 (nrf52840) connected to a SEGGER J-LINK to program it!
Using the J-LINK flash i can program the NINA B302
But, on VISUAL STUDIO +...
Hello!
I am having 3 nrf5340 devices; 2 Gateways and 1 Headset. I am trying to achieve the scenario where I can allow the Headset connects to selectively one of the 2 Gateways...
I recently got the nrf52840dk board and I am trying to use it with the Nuttx embedded OS. However, I am having some issues flashing the nuttx binary on my board.
this is...
I'm trying to accurately measure our 3.0 volt coin battery (CR2450).
Our product consume low power (<50 uA) and we measure the battery voltage every minute.
We must...
Hello,
I've been trying to get through SUPL client library license signup process but I my request get denied every time.
I think I've done everything that is required...
I wrote a firmware on my dk52 and am advertising some data to the nRF Connect for Mobile App.
Is there any way on how I can copy or send the received data (service data...
Hi,
I have the following ouput using the throughput example:
Altered output format a bit to give me the same for local and peer.
But I was wondering why there is a...
Hi All,
I am running nrfConnect SDK v1.8.0 ad started a new sample LBS project. I ultimately want to have 3 devices, 1 being a Central and 2 Peripherals both running LBS...
Hi
Nordic Team
I used nRF5_SDK_17.1.0. I have a very difficult problem:
I now only want to configure an RX pin and no TX pin. Can the serial port receive data function...
