Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I'm trying to modify the flash_fds example to write a start time when a button is pressed, then an end time when the button is released. I get the time over TWI from an RTC...
Hi, We are into Commercial health devices using nrf5340 and looking to use AoD technology for our device to get its indoor location. We need to have a Receiver with antenna...
What are different options to load the soft device on custom board? Currently, I am using nRFGoStudio to load the softdevice on nRF52840 DK. We will not have segger hardware...
My app uses a proprietary service and characteristic UUIDs; the app needs to completely manage all characteristic reads and writes. With nRF Connect, I can see my service...
Hi Community,
For community's help I success to create 12.3.0 DFU version get work.
So now I try to make all hex(softdevice, bootloader, application) to one hex file...
Dear Nordic,
We are trying to figure out the difference between the working/feature set of nRF_crypto file and mbedtls.
Which one is better and why?
Ambimat
Hello,
I wanted to ask which uart library we have to use in SDK16 and which configuration to have a LOW POWER UART
We are in development phase on the devkit PCA10040 and...
Hi guys,
So i have some Nordic DK board including some dongles, NRF52840 DK, NRF52833 DK running with Zigbee and thread SKD 4.1.0 and make a mesh out of them. But I have...
Hi,
I have to control 16 pin output pins based on the 16 pin interrupt.
Is it possible to have 16 pins interrupt in nrf52840 . Pin change interrupt
when i config
...
I use SDK 15.3, nrf52840.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/setting-up-the-timeslot-api
Normal use most of the...
We are developing a new product that requires extremely low power consumption with a target to run advertising intervals of between 2 to 10 seconds.
We are using the nRF52805...
Hello everybody, My nRF9160 simply does not connect, I already followed all the instructions that come in the quick guide, I successfully registered the SIM card in the nRF...
I am using nrf52832_xxaa with SDK v16.0. I have a requirement to write into UICR register use seggger but I don't see any sample for that. Is it possible? If yes, please provide...
Shalom!
I am getting with the nRF9160, BSD TCP sockets, a connect() errno=116 after disconnecting and closing a previous TCP connection.
I have two TCP servers with the...
