Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I would like to use the Shield Debug (P20) on the nRF52840DK as part of a Device Under Test platform for production devices. I also want to be able to transmit/receive data...
Hi,
I am playing around with the the Bluetooth Mesh SDK (`nrf5_SDK_for_Mesh_v2.1.1_src`), more precisely with the light-switch `proxy server` example. The nRF52 DK's LEDs...
I want to use nRF Sniffer for Bluetooth LE with Raspberry Pi 4, is it possible? Wireshark is used for frame capture.
What I did below ① Write sniffer_nrf52840dongle_nrf52840_7cc811f...
Using: ncs v1.4.0, Modem FW v1.2.3, SES v5.10d
I have a custom nRF9160 board with code based on the Asset Tracker app. I have GPS triggering off of the accelerometer. GPS...
The PDK does not show up in file explorer. Power switch in VDD position. LED 1 is on solid. The device manager universal Serial Bus controllers does not list any device that...
Hi, sorry for adding more posts on the same issue, but I don't see any of the posts that speaks to my current situation. I'm using nRF51822 and SDK 12.3.0, and I'm trying...
I am using NRFSDK 1702. I have one NRF52840 as central and multiple peripherals. The central receives data from the peripherals and then transmit the received data via hardware...
Hello,
I am trying to create an application that uses the mesh light lightness [client/server] model using the example application as a guide and I have a few questions...
I want to check which version of BLE is implemented while using a particular SDK or Soft Device(SD). Is the version of BLE dependent on SDK or SD or both ? I couldn't find...
Hi,
We encountered a problem if we take off the battery during functionning.
The UICR Register is completly erase when we put back the battery.
The issue is with lost...
Hi - I have a MDBT42Q SoC board developed by Seeed Studio which contains the nRF52832 SoC. The board is powered as the image below and I can program the board through the...
SDK: nRF5SDK Toolchain: ARM GCC
Hello,
I have some devices out in the field using nRF52840s, using the non-SoftDevice bootloader, and a custom mechanism for reading updates...
While the nRF5 SDK offers great support for validating the SoftDevice and application firmware in internal NOR Flash on every boot, it looks like that's not the case for the...
I am using nrf52 DK board with SDK15.3.0 developing my application on top of ble_blinky_peripheral example .
How do add CTS service in my application ??
I have refered...
