Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi .. i want to send the temperature data to central in non connectable state ,( in advertising ), as well as data will change dynamically . Therefore how to broadcast the...
Hello We are using the nRF52840-DK with SDK version 16.0.0 connecting to an android device Galaxy Note 5 (SM-N920v, Android 7.0, API 24). I captured the HCI_Snoop.Log (viewable...
I am using this code on all 3 nrf52 Development kit ( DK ) for server, client and relay+proxy nodes as mentioned in below setup...
1) nrf DK named A works as on/off server...
Hello, I'm trying to map custom PIN mapping on my prototype board, based on nRF9160 DK. I had to remove the UART0 pins and map them for my purpose, but when I'm trying to...
In nRF SDK 1.2.0 and 1.3.0, there is a function to generate the public/private RSA keys in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrfxlib/nrf_security...
I want to develop the tool to download the firmware，so，I need to call the interface of nrfjprog.dll，but there aren·t the detailed descreption，who can teach me？
Question...
Hello, I am working on bare-metal with the BSDLib on a custom board. When trying to debug a specific case in which our server refuses TLS connection, I wanted to see which...
Dear all; I am an originally signal processing expert working on "positioning in smart cities" for IoT using bluetooth 5.1. As part of our new tasks, we are to evaluate the...
I have several nrf52832 based (similar) devices, all are programmed once (at least), now when i try to update program some of devices cannot be programmed (about 5...10% of...
we make the tracking system. so, we want to measure the voltage of li-po battery (i am using nrf51 sensor tag with li-po battery), so, their is any circuitry or any API or...
Hi!
Program enters infinite loop in `sd_ble_gap_adv_start`.
Setup: I've seen https://devzone.nordicsemi.com/f/nordic-q-a/11818/sd_ble_gap_adv_start-hangs-after-disconnect...
Hello,
I've been trying to get a Thingy:91 to connect to the nRF Cloud from Shenzhen, China.
The modem is updated to mfwnrf9160120 and the firmware is on thingy91_nbiot_dfu_2020...
Hello,
I Have a custom PCB with Fanstel BT832 module soldered. Because that module does not have a 32 KHz quartz I need to set use the internal RC source instead. The problem...
