Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I want to convert APP_TIMER_TICKS ms to us.
So i'm using this function.
And, the value of APP_TIMER_CONFIG_RTC_FREQUENCY is
Also this is main code.
And, I...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello,
Is there a modified radio test firmware available? I am hoping for something that can be connected to via BLE, command it to turn on a tone, and then reboot the processor...
Hello,
I'm trying to send and receive data between the nRF52832 chip and a phone by following this tutorial:
https://github.com/bjornspockeli/custom_ble_service_example...
Hello!!
We are carrying out a project using nRF52832 , in which we must send a data to a phone every 1 second for 10 hours. The data sent is a sequence of numbers from 1...
I'm using Eclipse CDT for debugging according to the tutorial on this site. I've installed the device pack and I do see the nRF52 peripherals in the debug view. However all...
Hello Out There,
The Getting Started, it states as follows.
The following steps are required for nRF9160 DK versions UP TO v0.9.0. Newer versions of the nRF9160 DK contain...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
Hi Friend,
I use nrf252832 MCU and SDK 15.3,
I would like to Implement below function,
1:Device bond phone A without password first , the phone A popups a bonding dialog...
Hello. I've migrated my application from SDK 14.2 to 15.1 and I obtain this strange message from peer_manager_handler in my log: I obtain this message only when I connect...
Im trying to enable the Scheduler on a mesh example, but Im getting "1127959>, app_error_weak.c, 108, Mesh assert at 0x0002C9E4 (:0)" each time I try to add or connect it...
Hi,
I want to close uart by using app_uart_close() for low power, but can not init uart again by using app_uart_init() or nrf_drv_uart_init().
More I had try TASKS_STOPRX...
Hi All.
I am trying to use the " ble_advertising_advdata_update" function, but my compiler is giving me the following error. Which class do I need to add?
undefined reference...
Hi, I recently updated the "Toochain Manager" app inside "nRF Connect for Desktop" to v0.8.0, and after this update, the Segger embedded studio IDE just freezes when opened...
Hi,
I am using nRF52832 and sdk 16
I am done secure bootloader dfu. By generating the new firmware application. Zip , this part is working fine
Now I want to do buttonless...
