Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi, all
I have some questions:
1. Is the DFU advertising name could be stored in the dfu_settings_page?
2. How colud I change the DFU advertising name in the application...
In the specification of 6.18.12.7 IQ sampling，The d escription of magnitude and phase .
I dont understand about magnitude e quals 1.646756*sqrt(I^2+Q^2) ,Why about 1.646756...
I am using the discovery manager to do device discovery on any device that connects to my central. I there a way to read the data in the characteristic during this discovery...
Dear Nordic
I am using nRF5 SDK 16.0.0_98a08e2 , and studying the example ble_central\ble_app_uart_c.
I found that in function
BLE_GAP_EVT_ADV_REPORT disappeared, while...
Hi,
I can't find any ses project files for PCA10031 (dongle) in nRF5 SDK V16.0 when examining the [.../examples/ble_peripheral/ble_app_hrs] folder. Additionally, there doesn...
Hi,
I've been skimming through the NRF9160 FOTA samples and related libraries(1.1 and master) and having hard time to understand some of the basics.
My assumptions...
HI,
I want to power the system using a external regulated 5V source. Then nRF5340 must be used in High Voltage Mode. When operating in High Voltage Mode, the nRF5340 is...
Hi Nordic Pros,
I have a nrf52840 board, and I tried to connect it to my pc. It dosen't show up as "JLink" or "BOOTLOADER".
Inside Segger Embedded Studio, I tried to connect...
Hi, anyone call tell What is the acceptance rate of nrf52 series scanning
I'm used zephyr ble mesh example, One node sends, one node accepts, and the broadcast packet sent...
Hello,
When i build a project to the nRF9160 DK, the terminal shows output of the program. Everything works.
When downloading the merged.hex file to thingy91, then...
Hello everyone,
We are 4 students, who are developing a BLE mesh network to send data from a CANNBUS-simulator to a desktop. We have chosen to use the nrf52840 chip to set...
Hello,
I am using nrf52832 with SDK 16, I want to change advertising packet flags from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE(0x05) to 0x04 during run time how can...
Hi, Im developing an ac dimmer with zero crossing on mesh, but it flickers at low dimming levels, I even used the scheduler for the ble stack but it didnt help, what would...
hi, i am using nrf 52840 dongle , is there any support of AT commands to communicate with dongle .i want to communicate without using ui only by sending commands. if not any...
