Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I tried to get AWS FOTA exemple working but I have 2 problems:
With v1.0.0, LTE is connecting OK but I never get any MQTT event.
With last nrf commit version...
Hi support team,
I've been developing a project that uses a cycling cadence sensor and interacts with my nRF52840 DK which is the central device. I merged the rscs central...
Hii
I'm using nrf5_SDK_for_Mesh_v2.0.1_src with nRF52 DK. i have tested your light switch demo by creating provisioner, proxy client and proxy server on individual NRF52...
Hello, I'm newbie developer.
I want to create a program that ends advertising when I press the button and restarts press it again.
I've seen many examples, but I can't...
Hi Team Nordic,
I know this question has been answered in several threads but the responses seem quite old now. I am using nrf52840 and SDK 15.3.0 and I want to flash...
Module : EYSHJNZWZ (nRF52832)
Is there a way to check nRF52832 IC revision? Since the chip is embedded in the module, it cannot be confirmed by appearance.
Hello,
I am working on developing a program where the nRF52840 dongle is a central device and recognized as an HID keyboard to the computer.
I played around with the peripheral...
I am trying to get a periodic interrupt every 100 uS using TIMER4. My timers_init() code sets up the TIMER4 registers as follows:
My interrupt service routine for now...
Hello
I would like to evaluate the module in a place without Cat-M \ NBIoT support
is it possible (for evaluation purposes) to send the data by other means (for example...
Hi,
New to Nordic, new to SEGGER, and new to ARM, so forgive me if I'm just missing something...
I've been asked to write new code for some boards that have the nRF51822...
I am using the SPIM example in the nRF52840 SDK. It uses SPI_INSTANCE 3. I am doing a simple SPI Write of 2 bytes.
I get SS, SCK, working properly. MOSI is transitioning...
I want to take drive code from thingy sdk and apply it to nrf5 sdk uart project, but I don't know how. Please explain in detail because i'm university student ... thank you...
Hi Team Nordic,
I am trying to save my flash data after the DFU process but it keeps on erasing it. I saw a thread in which it was explained to increase the CODE_PAGE_SIZE...
Hello,
I have a problem with app_timer.
My program need to use BLE UART for about 15 second then switch for just RADIO after.
To do so, I enable the ble stack as...
hello support team
nRF52 DK , Mesh 2.01
I am trying Experimental BLE RELAY example.
1. In first trial I am using 1 RELAY DK all works well.
2.In second Trial I am...
