Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Is there any documentation that talks about interface between board controller (nrf52840) and nrf91 on nrf91DK
How do they interface. Is there sample code to create custom...
Hello all,
I am working on the DFU on the NRF52810 custom board
I am trying with secure bootloader example PCA10040e
with sdk 15.3 s112_nrf52_6.1.1 softdevice
Then...
Central and Peripheral are connected by BLE.
The following error may be displayed when sending BLE message multiple times to the peripheral at the same time.
>> NRF_ERROR_RESOURCES...
Hi,
I found a bug in fds module ( Flash Data Storage ) which lead to data system corruption.
Scenario:
Given the device started GC(Garbage Collection) procedure...
Hi,
I have found a bug in the fds module (Flash Data Storage), which lead to losing "installed pages". If it was a swap page, fds module will be bricked.
Tested on SDK...
Hi,
I have written a short driver for the ADXL362 accelerometer, which I'm attaching here, and I've connected breakout board of the accelerometer from Sparkfun to the nRF51...
Hi there,
I have just upgraded the SES to V4.16 and followed the assistant guide in nRF Connect. I have deleted the old ncs folder (and all files) and also created a new...
I measure 184 uA of current during WFE. I've read in other posts that the nRF52832 should draw about 1.2 uA during WFE.
I've looked over the project settings many times...
Greetings,
I am using nRF52840 Dongle and nRF Connect v3.2.0 PC application to scan for nearby Bluetooth devices and connect to them.
I want to develop a PC application...
Hi, I use in my design a component which use the nRF52840 - WLCSP package.
I use SPI to connect the nRF to a SD card slot. With the package, I understand that pin K4 (P0...
Hi all,
I am debugging the data transition flow of the Node with Relay.
We modified the example of ONOFF_server. We found that the unicast address should the odd number...
Hi, I cannot find my Nordic Thingy91 as a USB connected device in the nRFConnect desktop application.
I tried to connect the Thingy via a JTAG 10-pin cable via an external...
Hi,
Greetings!
I am trying test DFU example for nRF52832 and I need help to move ahead.
Setup:
nRF52832 SDK for Mesh V3.1.0
nRFSDK V15.3.0
nRF52832 Development...
Dear all,
I just played around with the nRF Sniffer and I am pretty impressed. Really good tool and most of the packets are received.
I want to build an application where...
I have reprogrammed the nRF52840 board controller. When I run the lte_ble_gateway application I get the following on the 2nd dev kit VCP port:
SPM: NS image at 0xc000...
