This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm using this example of code (nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132\arm5_no_packs) with my custom board to perform a dfu....
I have a peripheral device based on the nRF52832, using SDK 15.3.0. It uses a bunch of the standard services, including the TX Power Service, plus a custom one. When I connect...
What would be the best example to start with if i have to send the sensor data from nrf52840 to a mobile application using SDK for mesh? I have asked this question before...
Hi, could you tell me where I can find a sample project with button-less DFU-OTA and an application like ble_app_gls?
1. I use Windows 10; Embedded Studio; nRF52840 DK;...
Hello, We are using the NRF52840 and softdevice S140, PCA10056 on all examples. SDK version is 15.3. We see a problem following the secure OTA DFU protocol regarding acessing...
Hi,
I'm developing and testing the code using the PCA10040, but this board uses the NRF52382_XXAA which contains more memory and I want to use the NRF52382_XXAB. So, how...
Hello guys,
I have coin cell powered nRF52832 based sensor node. I develop the firmware in Segger Embedded Studio, SDK15.3.0.
On the pressure of a button on the sensor...
Mesh SDK:3.2.0
I want to send dimming level to server, and want return data of dimming level with mcu voltage.
When I receive server set callback, I tried: status publish...
I am developing a beacon-related project, my nrf51 device needs to play beacon. Beacon will determine the distance from NR51-> Smartphone. If distance = distance I give, I...
Hi all.
I am using a nrf52840 with mesh sdk 3.20 and sdk 15.30.
I am implementing RSSI tracking and require reference nodes to advertise once on each channel (37,38,39...
Hi guys,
I am using nordic semiconductor nrf52840 development board and segger. Is it possible to display the data of ultrasonic sensor on the nrf connect app by configuring...
Esteemed Colleagues,
We are using PCA10040 (1.2.4 2018.16) to develop a customized NFC Type 2 TAG. SDK 15.0.0 was used because we needed to work with hal_nfc_t2t.c instead...
Hi Team,
I am developing a low power application where we need to update Firmware frequently based on use cases.
I have successfully tested BLE secure DFU example and...
Hi,
We're trying to characterize the radio timings of the transmission of a Bluetooth Mesh packet from an originator in a Bluetooth Mesh network. Looking at the broadcast...
Hi,
In your nRF5 SDK v16.0.0 release note, I recognize that a new feature is added:
I am wondering which BLE event is indicating that SD has been free from BUSY state...
