Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I'm trying to run the usbd_cdc_acm example from SDK 15.3.0 on the nRF52840 Preview DK. While debugging, the code was running fine until I connect the nRF USB, at this...
Hi,
Is it expected to get an EINPROGRESS error when calling nrf_connect() with NRF_O_NONBLOCK set. How do I know if the call was successful or not? Should I expect a positive...
Tested with PCA10040 1.2.4 bare board Chosen p0.11 as it seems to connect nothing (floating)
I would expect the code below always prints "<info> Main: [11] 1 1 1 1 1", no...
I'm working on a custom DFU bootloader using the Secure Bootloader example in the nRF5 15.2 SDK. My board only has one LED and, during DFU, I'd like to using blinking duty...
I am using SPI 2 (not SPIM) and just migrated my project to SDK14 from 13.1.
I kept getting "Wrong configuration" on compile, until I realized that on the nrf_srv_spi.c...
Hi!
nrf52832, SDK15.0, central side. S132.
I connect my nrf52 in HID mode to android smartphon Samsung А8+ Android 9.
In a log I see connect- disconnect with error code...
Hi,
When using CFUN=0, the modem stores settings (such as system mode and successful network connection information) to the flash from what I can gather, but it then needs...
At certain times, I would like to disable the SoftDevice's control of the PA/LNA control lines and return them to normal GPIO lines.
When the SoftDevice is using the provided...
I am using nrf52832 module with SDK 11.0.0, s132. I am advertising and the central device is able to scan the advertising devices and displaying the RSSI and peer address...
Hello again Nordic World.
We are slowly attempting to transition from the nRF51 environment to nRF52. We are starting, not with development environment for our product,...
IN-119
it says t he affected versions are:" All versions of S110, S120 and S130 S132 v2.0.0"
does it means all versions of S130, or only S130 v2.0.0 affected?
When using ` nrfutil settings generate` to generate bootloader settings and merging with soft device and App, how do you then use `nrfutil pkg generate` to generate a package...
Hello, I am working on the modified versions of hrs and hrs_c examples, on two NRF52832 with s132. I modified the apps so that when they connect the peripheral reads from...
Hello,
I have a fewURGENT questions.
I have the NINA B112 by u-blox on a custom PCB (datasheet here ). We require regulatory testing of the BLE. The NINA B112 is based...
