Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello.
I am trying to migrate from sdk 11 to sdk 12 and I am having difficulty in adapting the device_manager.h functions that I am using in my code to the peer_manager...
Hi
I would like to be able to (force) stop characteristic notifications at some point in time.
Imagine a smartphone connects to peripheral and enables characteristic notification...
Hello,
I wanted to test the range of long range bluetooth using two nRF52840 USB dongles with the blinky example firmware of the nordic SDK 15.3 combined with softdevice...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have very basic query...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
RESETREAS will give cause of reset. But for...
Dear Team
I use the Lwip_mqtt_publisher example from the SDK 15.3 with a PCA10056 board.
Also, I used an Ubuntu 18 Instance(IPv4, I used 6tunnel) to run the Mosquitto...
Hello sir ,
I have conneccted an BLE400 dev kit to an swc J-flash device. And i can't erase it.
Tried with nRFgo Studio on windows 10 an with linux nrf cmd line...
Hello,
I am using the chip nrf52840. I am trying to configure three pins (P0.09, P0.10 and P0.11) as output pins and I am trying to make set and reset functions for them...
Hi ,
I am using NRF52832 ,SDK15 my code is based on the HR_FreeRtos project , I am using the nrfx_wdt API to implement WDT in my code .
I am using a LDO for the voltage...
I'm developing a product that use the Nordic UART service over BLE and need something similar to a USB serial port, except with NUS. Is there a Windows 10 driver that works...
Dear Nordic Team,
Thanks for supporting.
Currently i am working in Mesh network. My application is Single Client control 100 Server Individually . Same like this https...
Dear Nordic Team,
Thanks for supporting.
I am new for mesh network concept. I want to control individual device in mesh network (May be more than 10 device). I have tested...
Hi,
I have a project that has a bootloader based on the SDK15.3 secure buttonless DFU example. During pre-production testing, the need for downgrading the app came up. So...
Hi,
I just wanna start off by saying I know there a lot of similar posts to this one here on the dev zone, but my problem with them is that none of them (from what I've...
