We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
We are developing a GPS tracking device using nRF9160 module.
We want to use a battery as long as possible maybe for 7 days.
Here we need two cases for our application...
Hi,
I am using the BLE UART central and peripheral to send 100 messages of size 65 bytes (64 bytes + new line) continuously to the peripheral in the hope that I can see...
when ble central set BLE_GAP_IO_CAPS_DISPLAY_ONLY ,i find ble central no need to send the static passkey or send one wrong static passkey,ble central can connect ble peripheral...
I'm using the recommended code for handling errata 87 on the nRF52840.
Why is the Assert() necessary if this code works around errata 87?
Is there anything that could...
Hello,
I am currently working on nRF52832 custom board with SDK 15.2.0 and softdevice S132. I am using Segger Embedded Studio as IDE.
I would like to include an external...
Hi to all:
First post and new to the Nordic universe.
I'm working on an example with the NRF52840 usb dongle using NFC.
I'm using the nfc_meshcop example and change...
Windows 10, Keil5 5.27.1.0, Nordic SDK 15.3.0 59ac345, pca10056 devkit for nRF52840.
Works:
The DK shows up as "JLINK" when plugged into USB. I can copy the prebuilt hex...
I am currently publishing messages to a group of servers on a 10 second interval. This works well for a while but after a few minutes some of the nodes stop handling the message...
Hi! I am using Nordic Thingy : 52 Iot Sensor Kit. I have Windows x64 computer. I connected the sensor's bluetooth (nrf52832) to the HM-10 bluetooth module. I want to transfer...
I modified mqtt_simple program to test eDRX. This program subscribes a topic right after it is initiated.
I want to test only eDRX so set keep alive time = 30 min
I...
hi,
I am trying to readout the UICR info. But there is no such readout in the hex file using the programmer apps in nRF Connect.
There are 2 possibility, either blank...
Hi,
I am using nRF52832 DK and also my custom board based on nRF52832.
I have uploaded the application file into my device using OTA-DFU.
Now my device goes in application...
In my computer, I receive the error below
Besides that, the error also stated this: "Zephyr was unable to find the toolchain. Is the environment misconfigured?(Refer to...
Hi there,
I'm sorry if I'm asking something very simple:
How does one connect the J-Trace Pro to the nrf52 DevKit in such a way that I can get ETM functionalities? Obviously...
