Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am trying to integrate DFU into ble_app_uart example.
I am using nrf51422 board, sdk v10.0.0, soft device "s110_nrf51_8.0.0_softdevice.hex".
I have made some changes...
I'm trying to use Pin 0.21 as SCLK in the SDK15.2/examples/peripheral/spi/pca10056/blank/ses.
The example works fine with CLK on pin 3 (default) and on pin 29 (just tried...
Hi,
I created nrf52 project on Segger studio. I'm writing directly registers.(not SDK)
It includes i2c,uart and adc, this part is working now.
I want to add SoftDevice...
Hi,
I'm using Keil development tool.
The original bootloader start address is 0xE6000 and new bootloader start address is 0xE5000.
When I update to new bootloader, it...
hi...
What are the things I can check if I can't find my nRF51 upon scanning for BT devices? I am using nrf52832 and can successfully program the device via a Segger J-Link...
Simple and perhaps stupid, but important for me: the reports of detected devices I see in nRFConnect (desktop or mobile version) are based ONLY on BLE advertising packets...
Hi,
I am experiencing problems with the app_error_handler function defined in app_error_handler_iar_c provided with the SDK V15.0.0.
If the function gets called when debugging...
HI team,
I am a beginner of Nordic nrf52840 DK, I would like to control the AC ceiling fan using the nrf52840 board with pwm library. As, I can see we can use either single...
errr_code=sd_ble_uuid_encode(p_target_uuid,&raw_uuid_len,raw_uuid);when i debug and going to find uuid my debugger will move to NVIC_systemReset.i am running uart central...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
Hi,
I am currently trying send value to a write characteristic of the server of a custom central device with a nrf52832 peripheral device. I have been able to connect with...
Hi
I am going to use the ble_app_uart example , the sdk version is 15.2.0
I only modify the vendor specific UUID , and download in the NRF52840, it does not work, i can...
Hi there,
I am about to perform an RF emission test to my product which is using a nRF52 chip and different RF sources as wifi and cellular and I was requested to:
...
Hi,
Using the gls example, as soon as I try to connect to it using NRF Connect on my iPhone, I get the "Failed to secure connection. Disconnecting." error. Once the error...
Dear all,
I'm designing a layout with nRF52832 and in my layout I didn't use pin 37 and pin 38 (P0.25 and P0.26). I noted that in PCA10040 v1.2.1 development kit there are...
