Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am adding CLI service with my existing project developed based on ble_app_uart.
CLI Init function :
static void _cli_init(void) { ret_code_t ret;
#if CLI_OVER_UART...
Hi,
to be able to send more advertising data, i want to cyclical switch between different advertising packages. This already works so far.
Do i need to include the AD...
Hi there,
I am assessing the possibility of replacing a low-power MCU in one of our products with an nRF device.
Currently, our low-power MCU spends most of its time in...
Hi, all. I am trying to add a GPS module to the nRF52840 DK, just like what is done at this post. https://devzone.nordicsemi.com/b/blog/posts/nrf52840-long-range-demo
But...
Hello,
I want to write multiple words using the usb keyboard. I am working with usbd_hid_composite example on SDK_15.0.0_a53641a. I am able to write just a letter using...
i.e. it would be similar in type to the nRF24L01 radio code, but obviously different since it's part of the vastly different nRF52.
Any examples to draw upon?
Unable to get logging information for SAADC example project in SDK versions 15.0.0, and 15.1.0.
I have no problems accessing the logs for the ble_uart_app example project...
I want to do power profiling in my nrf nrf51822 devices. Nordic don't have any online tool to calculate current consumption for the nRF51 series. So how to calculate current...
Hello, We are using nRF51822, SDK12.3.0 and softdevice S130. It is a multiprotocol application using the softdevices' timeslot feature: Our protocol running in timeslots concurrent...
Greetings,
We are currently certifying a device to be compliant with FCC & IC rules in the US & Canada. The upper band edge measurement is failing on advertising channel...
Dear Support,
We are in pre-certification phase with our product using nRF52840.
For RF testing purposes, our testing house asked us to provide the following, and I am...
Dear Nordic,
I configure a GPIO pin to PWM output, from this diagram, if we enable `PIN[0].CNF.INPUT`, we can read GPIO status while the PWM is running. But I check the...
Hi
Am I alone in my judgement that some of the Nordic Example code is a good example of how NOT to code? These examples should demonstrate the perfect way to utilise a given...
I want to develop a custom Firmware for the Thingy:52.
I am using a Segger Edu J-link Debugger and the Thingy:52 PCA20020 Version 1.0.0. As an IDE i am using 64bit Segger...
Hi
We met the problem is that clock low time period is out of spec, we got the value from oscilloscope is 1.24us@pull up resistor 10K/7.15k when clock speed=400kHz. The...
