Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
error: L6050U: The code size of this image (34744 bytes) exceeds the maximum allowed for this version of the linker.
I tried to add rtc calendar program and call it from...
Hi,
want to try out the nRF52x Family, so will buy the DK board, which IDE is recommended? I am familar with VS Studio or Atmel Studio 7, so is there something like that...
Hi:
I want to capture the parameter of a digital wave like this, I want to get every 't' value. The wave is same in a period of time, but the 51822 capture value of 't' is...
SDK: 10.0.0
Softdevice: s110_nrf51_8.0.0
I'm working on migrating our application from SDK v9 to v10. I'm getting a softdevice assertion failure in src/rem.c line 1371...
Hi,
Can I use power profiler kit for current measurement of nRF52840 SoC?
If yes is there any hardware and software revision version(s) for power profiler kit?
Please...
I created a BLE Peripheral to read the light intensity, the purpose is connected to the iPhone device to read the update value in the BLE_NRF_52 device.
For the calibration...
Hi,
I checked this thread https://devzone.nordicsemi.com/f/nordic-q-a/24611/how-to-change-the-name-of-bootloader-s-dfutarg which suggests to modify the macro but I would...
Hello
for my project at the university I have to implement a bluetooth mesh network using 4 nordic thingys:52 and one nRF52DK(only for programming purposes, not part of...
Hi All!
I use Example Project from SDK: "examples\peripheral\usbd\" as reference to implement my HID device simple protocol (EP1IN / EP1OUT 64bytes)
The Question is how...
I am working with the BL652 Module from Laird, and with Keil 5, using a ST Link SWD programmer clone.
I am using the ble_app_uart_timer_driven_scan_mode from the ADC examples...
Hi, I am developing an IoT sensor (peripheral device) using SDK v11.
On my sensor, I have defined an advertising packet that broadcasts the complete local name and a scan...
I'm in the process of porting my application from SoftDevice S132 v4.0.2 / SDK v13.0.0 to SoftDevice S132 v6.0.0 / SDK v15.0.0. I noticed that the define for BLE_GAP_TIMEOUT_SRC_ADVERTISING...
Hello,
I'm attempting to use a high-limit reached event from the SAADC to trigger the clearing of a GPIO. My wish is to disable this GPIO with the lowest possible latency...
