Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I use the SDK9.0，When a bluetooth device and android APP to connect, disconnect the bluetooth device power, why wait for 20 seconds, the APP to detect device has been disconnected...
Hello Everyone,
I want to know that i purchased NRF51 DK ..which includes PCA10040 IC.i'm using MDK ARM KEIL5 . now if i'm going to develop one BLE product so i don't know...
Good morning.
I have two nrf-51 boards and a mobile device, the SDK that I´m using is the v.12.2.0. I need that the three devices are connected at the same time and its...
Hi all,
My configuration:
nrf52832
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using th e secure bootloader example located at \examples\dfu\bootloader_secure_ble...
The nrfgprgret register is used from the application(custom) to trigger the system into dfu mode. The nrf 52 enters dfu mode and a zip file containing bootloder.bin/.dat and...
hello, I check the standard example nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs device nrf52DK PCA10040 V1.1.1 ARM Compiler :...
I am currently considering purchasing the UBLOX NINA-B1 module. This uses the Nordic nRF52832.
The very 1st thing I wish to do is to be able to send and receive information...
Hi Nordic,
I have managed to make a board which has both the nRF52 and PN532 modules on the same board (picture) , connecting it through I2C as shown on the example here...
The Event Generator Unit peripheral is new in nrf52. There is a basic description in the current manual of nrf52, but not much can be inferred as to how to use it. Could an...
Hello All Supporters,
I'm developing one NRF51822 based product.so sometimes will need to update application codes as new features arrives.so if my user update(replace)application...
Hi there,
I'm testing the "saadc" example : <InstallFolder>\examples\peripheral\saadc
I haven't changed the code.
To do this, I use the nRF52840 with SDK 14.2 and s140...
Hello,
I am probably beating a dead horse here....
I am evaluating the PCA10056/nrf52840 preview DK and using the Keil/uVison 5.24.2 for that purpose.
I have found some...
How to have control(play/pause & previous/next) over the Google Play Music app via a BLE link. I know I need HID over GATT but I downloaded the official doc and I cannot understand...
Hi,
I would like to use the nRF52840 modules for moving nodes. However, I'm concerned that the modules will not be able to cope with high moving velocities to communicate...
