I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
I am using the LORA Drivers provided by zephyr for testing my SX1762 lora module with NRF52833 Development Kit. I am able to initialize and configure the LORA Peripherals...
Hi,
I am working on an FCC cert of our product which is nRF52811 based. We are currently on SDK 2.0.0. I have copied from the nrf samples bluetooth area the projects peripheral_uart...
1.After I burn AP CODE, executing "nrfjprog -f nrf53 --program factory_data.hex –sectorerase" instruction will cause the following error. This issue wasn't happened in prior...
I am trying SPI Master/Slave communication between two nRF54L15-DK boards, using the nRF Connect SDK v2.8.0 and nRF54L15-DK 0.9.1 and 0.8.1. However, it seems that the SPIS...
Hi,
I just got my Thingy91x up and running, and it’s been on for a few hours now, but it has already used 460/500 location requests. How often does the unit send location...
Hi, I am trying to flash to a new design which uses ublox NORA-B120 module. I am trying to flash from vsc. But the flashing fails with following error.
Anyone can help...
Hello,
I have configured 2 nRF5340 boards for LE audio streaming from my mac. Two things I am noticing:
1. The audio is streaming but it is intermittent. Audio plays...
I found out nrf_reset_network_force_off() can be used to turn on/off the network core in firmware, per the example in NCS v2.5.0, samples/subsys/ipc/ipc_service/icmsg . I...
Hi,
I am making an application based on the peripheral-nus example. The checking for CR is removed and all characters are just sent further when available. The problem is...
Hi, I have developed a stable program on the nRF52840 board, and now I'm transporting all the code, and trying to make it compatible with an nRF54L15 board.
I used ZMS to...
Howdy,
I am currently working on the nRF52840 chip and trying to convert my SPIS code from being in my main while loop into being interrupt driven. I am using Zephyr to...
Hi!
I want to integrate power management into our FW. Therefor I did enable it in the prj.conf:
And added runtime enable and action run calls regarding this device...
Hi,
Is there a sample demonstrating the EasyDMA configuration for the I2C21 peripheral of the nRF54L15 using SDK 2.8? I found a sample for the nRF52 with an earlier SDK...
HI,
I am super confused about which direction to go forward...
I need example code and tool chain where I can build a
1) ble bootloader that supports the Nordic Semi...
