Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I've been experimenting with the Mesh SDK (v3.2) on nRF52832 boards. After doing some end-to-end latency experiments, I've come up with some questions associated with...
51822, S130, SDK11.0. In order to save current, I disabled fast adv and set the slow adv interval to 10seconds. The current is low now, but I am facing connecting issues with...
with regards to nrfconnect ios v2.2, has anything changed with respect to service changed characteristic or service and characteristic discovery?
(behaviors described seen...
Hi nRF team,
I am configuring my GPIO pin with below code sample.
out_config = GPIOTE_CONFIG_OUT_SIMPLE(false);
err_code = nrfx_gpiote_out_init(MEM_SPI_SS_PIN, &out_config...
in ¨¨Blinky example¨¨ we press button on one board and led get ON on other board.
I want to ask how can I modify this example or any other example
what are the functions...
Hi
I am looking for BME680 example code for Thingy91,since I donot have access to NB-IoT / LTE network as of now, i can't use the asset tracking demo code. I just need BME680...
hello
we used sdk_15.2.0 ->proprietary_rf -> esb_ptx example to check 52840 transmission.
now we have 61440 bytes need to be sent out. i used following code；
int main...
I`m searching after a document / description how to setup a user test case for BLE RF distance range measurements. Maybe Nordic have a smart phone app which we can use to...
I am evaluating NRF for a commercial project. I am also new to this BLE business so trying to learn fast.
I am trying to run the supplied BLE UART example on the NRF52DK...
I am trying to develop a low power scanner with nrf52832 which is is acting as both central and peripheral (beacon)
I need to detect other tags like itself transmitting...
Hi,
is there any example of firmware that can be used on nRF24LU1P that perform some data receiving on RF side and send them over USB?
The most important part is the USB...
Hello, We have designed a PLE peripheral based on nRF52840, SDK16.0, Softdevice v7.0.1. We have having an issue where, occasionally, we send a certain data (a command) to...
Hi everyone,
I created a custom service that I want to be advertised through scan response. Also, I want to advertise the INFORMATION SERVICE through advertising data. I...
Hi, I'm working with nRF52840 with NFC. I don't have yet the external antenna to connect to (now I'm using uFL), but I'm not sure about the trace width that goes from the...
MeshSDK: 3.2.0
StockSDK: 15.2
Hello,
I have a network where the sequence numbers have become corrupt due to removing devices from a network and then provisioning other...
