Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
In BLE, a shorter connection interval reduces transmission latency and increases power consumption. Do we have any mathematical expressions to show this?
Thanks in advance...
Hi Team,
We are using nRF9160 DK without sim. We would like to connect to the other nRF9160 without BLE. Is it possible?
As we use SIM for only authentication right...
I use Nrf52832 and sdk16.0.Use I2S play sound.
This sound file comes from https://github.com/NordicPlayground/nRF52-teensy-sgtl5000-audio/tree/master/Convert%20Audio%20Sample...
Hi Sir,
I'm using nRF52832 + SDK 14.2 for building the OTA DFU function.
As checking the folder "../external/micro-ecc/", for nRF52 family, I found there two difference...
Good day.
I am busy evaluating the nRF9160, but when he builds his project he's getting the following error.
mkdir(modules/nrfxlib/nrf_security/src/mbedtls/CMakeFiles...
This is not a question. But it may save you sometime. :-)
Remember to zero this variable before call fds_record_find.
fds_find_token_t ftok;
Actually it is mentioned...
Dear Community,
I am working on a project where the idea is to build a board that can measure the resistance over a small biosensor. The biosensor will be connected between...
nRFConnect for Desktop v3.3.0 App: Bluetooth Low Energy v2.3.2 Windows 10 x64 ( 19.04, 19.09), using Dual Monitor. Device: PCA10059 or PCA10056
I can start, connect, and...
In the "Cellular IoT development on Nordic Thingy:91" video (-> https://webinars.nordicsemi.com/cellular-iot-development-on-nordic ) an nRF Connect SDK Toolchain manager app...
SDK14+Nrf52832:
I want use one pin as a interrupt pin.
when the pin level from high to low, execute A task;
while when the pin level is from low to high, execute B task...
Hi Folks,
Windows 10, clean install of ncs v1.2.0, using nRF5340-PDK with SES 4.42a. Project blinky rebuilds and runs fine. Now I need a zephyr example of creating a simple...
Hi,
What is the suggested way to switch between 64MHz and 128MHz on the application core? Normally I want to run at 64MHz, but sometimes boost it to 128MHz. Is there additional...
Hi,i use the bootloader demo code , the file path is nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_bootloader\pca10056_s140_ble\arm5_no_packs ,a fter I compiled and passed,...
Hi,
I know this question has been asked a million times before, but most of the links are now dead, and the advice seems stale. On sdk 15 and up, how do I go about setting...
