After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
what should I do in order to enable Bluetooth Low Energy on PC (mainly Windows XP to 8, but Linux or Mac would be nice if they don't support BLE natively)?
My device...
Last few lines of log
After looking into error code it shows 'DFU_END_ERROR_UNAUTHORIZED'. I followed procedure from here . Am I missing something here. Have flashed my...
how can i do a new characteristic ( all new 128bit-uuid )Under the same service
this is i try use nrf connect to do this , i hop add new different from NUS servic ( only...
I received the device and tried running the default asset tracker that was installed and kept getting these messages:
DEBUG modem << Connected to LTE network\x0D\x0A
DEBUG...
Hi, Why a smartphone cannot use Advertising Bearer to send/receive messages in a BLE mesh network? While it can do advertising for a normal BLE connection (pairing for example...
Hello, This is my third question in this respect and I have not received any response what so ever and I don't know why! It seems that the nRF mesh application uses GATT bearer...
Hello
I am trying to activate GPS on pca10090, VERSION 0.85, using asset tracker example, tag : v1.0.0-rc4
I get:
GPS initialized Starting GPS Enabling PSM PSM...
Hi,
We are using nRF9160 and want to use PSM & eDRX mode in one of our project. We referred 'Asset tracker Application' & found that lte_lc_psm_req() and lte_lc_edrx_req...
It would be great if I could move my project over to the Mac and use one less computer. But I wonder how well the tools work on MacOS platform. Are there any major limitations...
Hello,
the "Developing for nRF52810" user guide in the Infocenter says that to fully transfer a project to nRF52810 the defines DEVELOP_IN_NRF52832 and NRFX_COREDEP_DELAY_US_LOOP_CYCLES...
Hi
i am new with nRF52832. i am trying to run fatfs example program. But it shows Disk initialization failed. what is the reason for it?.
i am using segger embedded studio...
Hi,
I'm using SDK 15.2 & trying to combine hid keyboard with custom gatt service, but it was not advertising. When I debug, it got stuck on the line below with error code...
Hi.
I'd like to use nRF52840 in our project. Can I use the SoC and Zigbee SDK for commercial?
UPDATE!
Have I any limits if I will use SOC and Zigbee SDK for commercial...
Hello,
I follow " Configuring and performing DFU over Mesh" instraction and face with error after trying to transfer new app: "No response after opening COM port".
I do...
Hi,
I am trying to merge dfu with Beacon application. I have added all the required file in dfu example, but I am getting linker error for bsp.o file.
I am using sdk 14...
