Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi, nordic engineer:
Our project has a function, that is, BLE+Thread coexists. We hope that the mobile phone can upgrade the device through BLE. Can this idea be realized...
Hi everyone,
I am using nrf52832 with SDK version 11.0 for an IoT application. I am communicating with Atmel ATWINC 1500 module through SPI in order to connect to Wifi...
Hi,
I have a custom implemented DFU that I used in many nRF52832 designs.
This one in particular fails when I am calling nrf_fstorage_erase. I am trying to erase 40...
Dear all,
I am trying to work with FOTA. I am able to run successfully the http_application_update.
But now, I want the device to download a custom firmware that I...
Hi all,
I am trying to set up UART communication on the nrf9160. I am using the nrf9160 DK and zephyr.
I have selected device UART_1 and after I cal functions device get_binding...
Hi,
I am trying to implement OTA updates on iOS. Where can I find out what error 10 means?
Below is the log of events from my app. Please don't hesitate with questions...
Hello guys,
I have nRF52840-based BL654 SoC module on my custom board and I develop the firmware in SDK 15.0.0 environment with s140 SoftDevice.
Among other things, I...
One little example At the bottom of file nrf5SDKforMeshv310/bin/ospace/examples/dfu/dfu_nrf52840_xxAA_s140_6.1.0.hex
We can make it more human-readable by utility from...
Hello,
I'm trying to make custom board based on Thingy 52.
First problem that I get I want to change gpio's order according to my needs.
I can't not find where in the...
Since the manual for the nRF9160 DK doesn't have a full schematic, I'm not sure what sort of power supply decoupling the nRF9160 needs. What are recommended bypass caps, if...
Hello,
I've modified(added custom libraries) an existing example project from the SDK(v 15.3), and I'm trying to build and flash it.
The project compiles fine, but throws...
Hi,
I am using nrf52840 with an ADC that senses data and sends it via bluetooth. I want it to sense data, store it in the memory and then send it via BLE and then start...
Hello,
The current project I am troubleshooting includes an NRF51822 chip. The project includes a boot loader, application hex, and soft device S110 V7.3.0. It was noticed...
