When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hi
Freshly downloaded the SDK14.2 and trying to start a new development based on the fatfs example.
I connected a small Sparkfun SD card breakout to the SPI pin on my...
I am trying to read (the report map) and receive notifications (the report) from an HID device as a BLE central. The bonding process has been completedsuccessfully to my knowledge...
Hello,
I am testing the capabilities of Thingy:91, the first day I could see data in cloud (temperature and other sensors + GPS).
Today usage of SIM card grows up but...
Hello,
I'm trying to setup a new project and start experimenting with the nRF51 series. I'm a little confused about the needed files I have to add on the project to get...
Hi:
SDK version: SDK 13.0
MCU: nrf52832
For the purpose of saving power, the peripheral disconnect the BLE connection in the program when there is no data transmission...
Hello,
I am using nRF52832 EVM board with SDK 15.3.0 in SEGGER studio IDE, win 10.
When I am implementing sd_nvic_SystemReset(); in my code, that time i am not able to...
I have a custom board based on QIAA Reference Layout 1.1 Variant 6.
The application is built with Zephyr without bootloader and is placed directly on address 0x0.
When...
Hi, I'm designing nRF52832 custom board, on 'single side' pcb.
To make VDD and GND lines connect, I used 4 jumpers, which have 0 ohms.
I designed with nRF52832-QFAB reference...
I used the ble_app_uart for pca10040e successfully on the DK52, now I'm trying to port that project onto actual nRF52810 chip.
This is my build configuration on SES (Segger...
Hello Nordic Support Team,
The question I have is simple.
Can I use the pc-ble-driver with the ble_connectivity_s140_usb_hci example found in SDK15.3.0?
If not why?...
Is there any public documentation on the LTE Modem hardware API for the nRF9160?
I'm interested in porting an embedded operating system written in Rust to the nRF9160 and...
Hi,
I am using ncs 1.0.0 in nRF9160.
I have enabled UART 2 interrupt during initialization of the uart as below and it works fine.
To reduce the power consumption...
Hi,
Using the Thingy app on my iPhone works fine.
However, I would like using my iPhone as a gateway (thingy:52 -> iPhone (BLE -> Internet) -> nrFCloud. I installed the...
