I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello
I have ported the example project "nrf_crypto_aes_pca10056" to my one project. But now I'm not able to building the project anymore. Segger Embedded Studio will show...
Members
I am in the board design phase of my project. I use Arduino boards (Due & Uno) with SPI. I read that the nRF24L series is not recommended for future projects....
Hi,
So I am using nRF51822 chip to develop our products. We have two motors attacked to our PCB and we want to control the pulse with low power PWM. We want to control...
Hi...
i want to read the data from another board using serial uart .. how to write the command to check the data is available ... in arduino i written like this how to write...
Hello,
I used to use two nRF52810 for testing.
Using Timeslot (BLE+ESB), one of the 52810 paired mobile phones Bluetooth simultaneously sends the ESB.
Another 52810...
What are all the configuration options necessary to configure the nRF9160 as a SPI slave? I'm working with a custom board and have specific DTS files I'm working with. Here...
Hi Nordic Team,
I'm quite confused and can't find a concrete answer so far on the forum, if it is a MUST to kick-off a certification at the Bluetooth SIG Group or not, if...
nRF52840 SDK 15.2
I want to control the power of sensor, so I configurate the pin like this:
nrf_gpio_cfg(AFE4403_PIN_PWR_EN, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_DISCONNECT...
HI,
I am using ".\nRF5_SDK_15.3.0_59ac345\examples\peripheral\wdt" to test “watch dog timer function.
My use case is:
1. If the program is not execute over following...
I have developed ble periphleral device to send 20byte long at every five seconds to the central. Because connecting to serial to PC, I didn't realize the device cannot not...
Hi,
I need to run RTC simultaneously with Softdevice without external low frequency clock source (32.768kHz oscillator).
I used following settings to setup RTC,
RTC_ENABLED...
I am trying to make a central device that is similar to the NUS central example in the SDK. I have a function that is the same as ble_nus_chars_received_uart_print to print...
In the ESB stack, only a sub-set of available transmitter powers are enumerated in nrf_esb_tx_power_t.
Is this deliberate? The hardware supports a much wider range of values...
I Performed a clean reinstall of all tools and packages.
core_cm4.h file exists at location: C:\..\..\..\..\..\Nordic\nRF5_SDK_15.3.0_59ac345\nRF5_SDK_15.3.0_59ac345\components...
