i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I doubt Nordic developed a brand new GPS receiver for the 9160. Where does it come from (manufacturer and model)?
The Thingy91 Asset Tracker out of the box example has some...
The Thingy:52 Environment Service uses this structure to represent Temperature.:
This is wrong - it cannot correctly represent temperatures below zero but above -1 ...
pls advise if nrf9160 DK can work in RDP protocol , say the board is in US to work on NBIOT carrier or LTEM carrier . Can it be configured in some way to do evaluation remotely...
Hello!
It seems to me that GCC compiler optimization (-O3 -g3) somehow break the SAADC.
When enabling said optimizations the SAADC no longer gives me valid measurements...
Hello,
I'm developing a gateway and i would like to use advertising packet on sensor side to transmit data but it suggests that my gateway will be in permanent scan. I know...
Hi , I would want to establish a GATT Server application as well as integrate Bond Management Service from glucose example (ble_app_gls) in examples folder of SDK15.3.0_59ac345...
ble_db_discovery_start () returns NRF_ERROR_INVALID_PARAM (0x7)
This problem occurs when two peripherals are connected to one central unit. The two peripherals use the same...
Hey,
I am having trouble validating this idea through research. I was hoping someone could give me some ballpark feedback.
The setup:
- 15 NRF52832 devices on custom...
all set. while in linking stage i am getting
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_sdh_is_enabled (referred from nrf_fstorage_sd.o). .\_build\nrf52832_xxaa...
Hi,
I am using NRF51422 dk board in our project.We are using SDK 12.3 version , soft device S130 and keil u vision. Here the problem is I am not able to connect the bluetooth...
Hello:
I am able to debug and output to the J-link RTT Viewer(V6.44e) and when I stop debugging or sometimes randmley, the Viewer will display the message
"Warring:...
We're using SAADC to monitor two different voltage rails in different combinations (sometimes one and sometimes both).
I'm experiencing an issue in the following scenario...
Hi
I followed below tutorial, and I tried to send scan response data
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising...
Hi, everyone,
We are developing projects with nRF52832/51822 chips by using development board PCA10040. The programming of the chips is done by “nRF Connect\Programmer”...
Hi,
I have a problem with the app timer firing incorrectly.
I am using development board nrf52840-DK, Segger Studio 4.22, SDK 15.3.0_59.
When there has gone more than...
