Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi,
I am a newbie and would like to build a solution that combines nrf51822 with Arduino. Is this possible.
I find that there are many nrf5001 + Arduino solutions, but...
Hi,
I try to use APP_ERROR_HANDLER(err_code) with a custom error code ( for example 25) in a custom function. Error code reported is correct, but error line and filename...
hello,
Have any example about how to use "CHANNEL_IN_WRONG_STATE" ?
I don't know how to use it. and also don't know when softdevice return this even.
///< Command...
I am having an issue with pin changes triggering interrupts using app_gpiote. I've set up app_gpiote to watch pin 30 and trigger an interrupt on low-to-high or high-to-low...
Folks,
I'd like to use the single UART peripheral in the nRF51822 in interleaved fashion to support two serial "ports", e.g., sets of GPIO pins dedicated to separate serial...
Folks,
In the latest SDK (6.1) for the nRF51822 I see two versions of SPI master code in the Source folder and examples: with and without "5W" appended to the filename...
Hello,
Been posting a few threads lately on my attempt to get the ble_app_hids_keyboard example to work on PCA10003.
I've gotten the files to compile using Eclipse on...
Hello,
i am measuring the current on my nrf51822 board. While sending messages over I2C i have a current about 4.4 mA.
This should be correct? The CPU, 1v2, hfclk and...
Hello,
i use the nRF51 SDK_v6.1.0.0 with s210_nrf51422_3.0.0_softdevice.hex and EM:Blocks as IDE.
i have included the SD210 into the project wizard and created the s210...
Hello,
i am currently trying to integrate a timer properly to my project.
I want to set a pin to high for a duration of 1msec.
I configured the timer like shown below...
Hello,
i am currently working at a project which includes radio transmission based on th hal_nrf library.
I am using parts of an example code, which worked fine for me...
Hello,
my application is using the event scheduler while the softdevice is not. Is it save to call softdevice functions (like sd_ble_gap_scan_stop(), dm_device_delete_all...
Hi,
We deloped some concept(it looks not very good - sorry) for unique device which can be a slave and master.
to use this demo need following
Download to PCA10004...
Hi,
we developing bluetooth solution with S130 soft device
From now there only one example appear and i start it sucessfully but got some problem below
I see that device...