After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi,
we are using nRF Connect SDK 2.6.1 with Tools Chain 2.6.1 on nRF52833 for a simple Broadcaster (ADV_NONCONN_IND) where we want to use Resolvable Private Addresses. ...
Hello,
I have been developing on a nRF9151DK v0.9.0 for a few weeks now. So far this board is great! However, I have been running some long duration tests recently and logging...
Dear Nordic Semiconductor Support Team,
I am using the Ebyte E73-2G4M08S1C module, which is based on the nRF52840 chip, for distance measurement purposes. I would like to...
I have designed and built a custom nRF52840 board and I’m experiencing difficulties programming it via SWD using an nRF52840 DK (version 2.0.1). When I connect my custom board...
Hi,
I am struggling a bit on how to correctly extract the device name of the reflector, which is present in the Advertisement Data.
The code that i have down below shows...
Hello
Following my previous message from yesterday, the service seems to no longer be usable again at the moment.
Could you please confirm that this is a temporary issue...
How is it possible to read the DEVICEID from the FICR for any Nordic family device in a generic way using nrfutil?
`nrfutil --json-pretty device device-info` does not include...
Hi,
I use the nRF9160 with SDK2.5.0.
Which MQTT version (3.1, 3.1.1 and 5.0) does it support? And w hich QoS level (0, 1 and 2) does it support?
Does it support QUIC...
Hi, Looked into public Nordic repositories in github looking for a recommended implementation of CTS (current time service) to use with this sample: https://docs.nordicsemi...
Hi,
I've got a question regarding the configuration I have to make in order to get the logs from the nrf9160 in the serial terminal using the hci_lpuart sample.
My setup...
I have been using a Chinese debugger ARM v9 which supports JTAG+SWD to debug my nrf52840dongle so that I can upload my custom bootloader with my code in it using SWD pins...
Hello,
we have produced 10 Boards with nRF9151. Unfortunately, 3 device shows a false behavior. We cannot connect over SWD an they have a larger power consumption (whole...
I want to implement FOTA Update for a nrf5340 based board by using nrfConnect SDK v2.9.0 with zephyr and mcuboot. The board has a MX25R6435F external flash (same as the nrf5340dk...
Hello,
I am trying to run a ztest integration example I found under this one here: https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/subsys/testsuite/integration...
