I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I am following https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.0/nrf/gs_installing.html for installing on Linux.
I have installed SES from 1.6.99 documentation...
I am trying to get use the Zephyr console sample for nrf52840dongle but when I have configured the following in my prj.conf file I get a link error.
When I reload the...
Dear friends,
From this case , we already know that the mesh stack will arrange a new block when the node is reset, so we will get a new sequence number. We will use the...
Hi, dear Nordic team. I would like to use buttonless OTA DFU for nRF52805.
Here is what I did:
Step 1) install all tools
Step 2) Build my ADC code, rename the output...
Hello
I'm going to use 'frequency hopping' to prevent frequency interference.
I don't know what frequency hopping is yet. May I have a good example and related documents...
Hi there
We managed to send/receive SMS on the nRF91Dk using the asset_tracker_v1 example, which contains the at_client.
However, with the asset_tracker_v2 we never...
Hi all,
Here's the context -
Hardware :
- nrf52840 DK
- sensor - LIS3DH connected via SPI
Software:
- SES
- nrfConnect
I need to send data being captured...
I've been trying to write a simple I2S loopback project for the nRF5340DK board using SES. Zephyr's documentation doesn't list I2S as a supported peripheral for this device...
I updated the firmware according to the video "https://www.youtube.com/watch?v=xQ7hDzRULJQ&t=314s&ab_channel=NordicSemiconductor"
File for "update modem" : mfw_nrf9160_1...
Good morning everyone,
I have questions regarding the initialization of UART communication between nRF52 and nRF91 on nRF91 DK.
Device HW/SW setup:
nRF52 DK: Bluetooth...
Hi!
We recently developed some firmware using S112 on a nRF52810 but realised that we needed data length extension, so changed to using S113.
Previously everything worked...
Dear friends,
I flashed a serial example( nrf5_SDK_for_Mesh_v5.0.0_src\examples\serial ) to my 52840 DK as a provisoner, I used this DK and PyACI provisoning new device...
Hi, I'm working on a project using s112_nrf52_7.2.0 in nRF52820.
Services are set in initialization function as shown below. However, only PnP id is not set in DIS, and...
Dear friends,
My 52840 DK flashed a serial example(nrf5_SDK_for_Mesh_v5.0.0_src\examples\serial) as a provisioner. However, the 52840 throws an error message when I input...
