I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi all
I have Openthread setup
BorderRouter [ with Raspberry pi and nordic in NCP design].
EFR32 radio board that has been flashed with ot-cli-ftd and made as Leader...
Kindly confirm modem details, BIP ,Refresh command support etc. as mentioned in sheet. -- Kindly let me know whether the question from the operator is clear
Chip nrF52810
SDK - 17.0.2
SD- S112
Mine is a system which sends out beacon continuously (no scanning).
From the spec, I see that the, 2Mbps is the only feature...
Hi
I am currently developing using GPIOTE, TWI, and TIMER.
There is no problem when TWI is only working, but when interrupt (GPIOTE, TIMER simultaneously) occurs, TWI...
Background : We developing lighting product and planning to use nRF52833 module and we planning to use the latest SDK version that is nRF5 SDK for Mesh v5.0.0. First step...
Hi,
We're doing some testing of mesh protocols and their latencies using the nRF5340 DK. We want to isolate the wireless communication from interference as much as possible...
Our project uses nRF Connect SDK v1.5.0. Two main developers work with the files in very different environments.
I am not sure if this was an accident of initial development...
Hi,
I am currently running a custom bootloader I found that updates via SPI. I have 2 nrf52840 DKs that are programmed as an SPI master and a SPI bootloader. I have been...
After developing with an nRF52 832 DK (pca10040), our code builds and runs fine. But when we try to use the same code on the nRF52840 dongle it does'nt work. We added flashing...
periodic_adv sample is not working with nrf5340dk_nrf5340_cpuapp
it is working for nrf52840dk_nrf52840 after adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf
Here is the log...
My problem is the that on some devices the ScanResult.getDevice() or ScanResult.getScanResult() both return null on some devices but works fine on most.
This is probably...
Hi folks,
I want to calculate the timestamp for which my thingy 52 board was scanning from another thingy 52(may be more than one board). Is there any technique to get the...
I am confirming ADC sampling 420Hz operation by following question.
https://devzone.nordicsemi.com/f/nordic-q-a/69096/1khz-or-more-adc-sampling-rate-over-ble
The source...
Hello,
I am using the nrf9160DK and I am implementing on zephyr.
For my application I need to write to an external flash memory through I2C. I need to write one page at...
Hello
We are using the NINA-B1 on one of our products.
The phone application is working 100% and was very easy to setup.
Till we came to connect our frontend to...
