I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Hi all,
As I wanted to try out the new extended periodic advertising examples (periodic_adv and periodic_sync) located under /v1.5.0/zephyr/samples/bluetooth of the latest...
hello,
i am using nrf52840 with our cutomised board and trying to achieve long range using coded phy and using that long range demo example as base i have sucessfully changed...
I try to send out sensor streaming data to terminal over BLE NUS. Sensor sampling rate is 100Hz and 6 bytes per sample. Is there a best option to do this if I need to send...
We're working on a product that is able to store around 400uC of charge (two 220uF capacitors). There is a constant input of 21 uA minimum coming from a small solar panel...
I'm using AT%XRFTEST=0,1,2,19300,-40,1 to test reception at 1930MHz on the NRF9160 DK with a CW generator, and I don't understand the effect of the -40 parameter. With my...
We are currently working on an energy harvesting solution that powers the nRF52832. The energy harvester is providing energy from indoor solar and at the lowest light level...
I'm kind of confused about the DCDCEN0/1 related functionality and can use some confirmation. If I'm hoping to run everything at 1.8V, it seems I can wire VDD_NRF to 1.8V...
Hello,
In our device, we would like to implement an HID Service for the most simple cases. This part is OK, there are examples for this.
For advanced users, we would like...
Hello,
MCU: nRF52832;
SDK: 15.3;
Project: examples\ble_peripheral\experimental\ble_app_ots
nrf52832 receive data from app, communication by L2CAP, I want to increase...
Hi,
I use library NRF21540.c to config to control NRF21540, to amplifier the radio of nrf52832.
This is my define:
#ifndef NRF21540_USE_GPIO_MANAGEMENT #define NRF21540_USE_GPIO_MANAGEMENT...
Hello!!
I want to implement I2C between nrf52832 and capsense button (CY8CMBR2110-24LQ) and want to put it to sleep mode so that I could get ~2-3uA if there is no activity...
Device: nRF52840
SDK: 16.0.
Softdevice: 6.1.1
Hello,
I'm using Timer 2 peripheral using simple timer driver. It's working fine but I have serious drift/accuracy issue...
I use SDK16 and softdevice S140. I use cdc_acm to simulate a UART port. My data traffic is very heavy. It cause data overwrite and send out many zero. My source code snippet...
Hi,
I have been trying to use nordic nrf52840 USB dongle/ pca 10059 in BLE mode to fetch data published through Bluetooth; however I can find any compilers that support...
I have adapted the example ble_app_gattsin SDK_17. My code is as follows:
However, an error is thrown when setting the scan filter as follows: nrf_ble_scan_filter_set...
