Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
I want to take drive code from thingy sdk and apply it to nrf5 sdk uart project, but I don't know how. Please explain in detail because i'm university student ... thank you...
Hi Team Nordic,
I am trying to save my flash data after the DFU process but it keeps on erasing it. I saw a thread in which it was explained to increase the CODE_PAGE_SIZE...
Hello,
I have a problem with app_timer.
My program need to use BLE UART for about 15 second then switch for just RADIO after.
To do so, I enable the ble stack as...
hello support team
nRF52 DK , Mesh 2.01
I am trying Experimental BLE RELAY example.
1. In first trial I am using 1 RELAY DK all works well.
2.In second Trial I am...
Hi everyone, I have a custom board using nRF52832 chip.
I want to turn ON and OFF a LED, which is directly connected to a GPIO pin.
Using this configuration I expect...
Hi,
I want to use the math.h for my nRF9160 project, but when I include it, it doesn't find it. I am a beginner and I wanted to ask how do I include libarys proparly in...
Hi,
I have two nRF54840 DK and I am testing ble_app_att_mtu_throughput example with the boards. I am using nRF5_SDK_15.3.0_59ac345 SDK.
The number on the chip is "N52840...
Hello!
Im getting a hardfault when trying to send 10 bytes data via NUS. I receive the data, but the app crashes:
0> <error> hardfault: HARD FAULT at 0x00000000 0...
Hi everybody. I know that it is complete standart question, which has many asks and solutions here. I'm quite new to bootloader management stuff. So asking about some targeting...
Hi,
I am fairly new to BLE application development on NRF52.
I have a temperature and humidity sensor TH02 and I have interfaced it by making essential changes in TWI...
I found a function, sys_reboot() that apparently reboots the nRF9160. In order to use this function, what must be configured and what are the correct .h files?
Thanks
Hello,
I am trying to configure my nRF9160 v0.8.5 dk for current measurement and found out that SB 44 is missing on my kit. As the user manual suggest that in order to enable...
Dear DevZone team, I am using Thingy91 in NB-IoT mode because I am located in Germany. Last week I managed to connect it to the nRF Cloud by updating the firmware (thingy91_nbiot_legacy_pco_v0...
Hi,
I have multiple sensor data that needs to be recorded in separate files. This data is being collected in parallel. Using the FATFS xample in SDK 15, I am able to write...
