I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hello everyone,
I have a custom board with an nRF5340, which currently uses the internal clock. Im using toolchain v2.9.0 and SDK 2.9.0.
I'm trying to use the RV8263-C8...
I have tried building the nrf example projects and they build fine. But this project gives this error.
The version I am using is SEGGER Embedded Studio for ARM Release 7...
here is 2 question for this example. (v2.9.0) as i looking for this example, there are some limitations like belows.
One BIG, one of the two BIS streams (selectable...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
I am developing a proof of concept project using Wave share BLE400 module and the final product of this project should work on button battery backup for years. so essentially...
Hi, I recently upgraded our ncs SDK version from 2.6.0 to 2.9.0 for a custom matter application development using an nRF5340. We also support a smaller debug app that is BLE...
When setting the following channel sounding parameters with bt_le_cs_set_procedure_parameters I am getting E: Failed to set procedure parameters (err -22) or BT_HCI_ERR_INVALID_PARAM...
Dear,
i think that the evb nrf52 dk missed the bootloader because when i push on Segger (target connect j-link), there is the message NO PROBES CONNECTED VIA USB.
I...
Hi,
We are currently in the process of evaluating the nPM1300 PMIC for our project and I would like to know if there is a way to supply Vsys using the battery even when...
Hi, I'm in India Using JIO 4G sim card in India can't connects to NB-iot . Here network provider supports NB-iot but if i try to connect the network it is searching for a...
Hello,
I have always been able to use VSCode to find various installed toolchain versions, but today I suddenly cannot find toolchains other than v2.2.0.
I checked and...
Hi
I have a beacon sending out some data, and I have already finish the TX side, I also want to have a RX side to receive the data, in addition, as there are many other...
GNSS not working on Thingy:91 after modem_shell flash — help and gnss start return ERROR
Device:
Thingy:91 (NK-THINGY91) RS Stock No. 196-3901 nRF9160 + nRF52840 combo...
Hi Nordic,
I’m new to the nRF Connect SDK for VS Code and currently evaluating the nRF7002 DK board. I’ve been able to build and debug firmware successfully for the NRF7002DK_NRF5340_CPUAPP...
If you see i'm trying to install toolchain and nrf sdk v2.6.1 via vscode, the installations seems to be successful but at the end of toolchain as well as sdk installation...
