Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hello,
Is it possible to configure an nRF5340 to be both a Broadcast Sink and a Broadcast Source, but with the condition that only frames received by the Broadcast Sink...
Hello,
I am measuring RSSI values with nrf_modem_dect_phy_rssi(...) from the DECT PHY firmware.
The nrf_modem_dect_phy_rssi_event refers to positive values being saturated...
Hello, I have a particularly weird problem that I can't figure out how to solve. I was using the 52833 DK for software development and the onboard leds were blinking perfectly...
Hi.
I'm fighting to get an i2c scanner (re)expose external devices' hex addresses on an Xiao nrf52840 board under VsCode nrfConnect (the basic board, not the Sense version...
Hi,
we are designing a custom board based on the nRF54L15 QFAA (QFN48) using a chip antenna with coplanar waveguide feed on a 4-layer PCB.
In the Nordic reference design...
Hello, We're improving a battery-powered (CR2032) sensor tag based on an NRF52833 with a 868 MHz transceiver. We want to use the nPM2100 PMIC and would like to optimize the...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Dear Nordic Team,
We are seeking assistance in resolving a significant power consumption gap observed in our nRF9151-based asset tracker. While our lab testing suggests...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hi,
I am working on a custom board based on the nRF5340 using Zephyr RTOS with external QSPI NOR flash.
I am facing an intermittent issue with the external flash.
Observed...
Hi nordic,
I am streaming live microphone PCM data over BLE. The microphone data is continuously captured and stored in a buffer. Whenever 12 KB of audio data is available...
I am PHD student in china and doing research about gait retraining. I am designing wearable sensor that monitoring gait and giving vibration feedback to retrain the gait and...
we would like to explore the Nordic nRF52 series of low powere BTLE on coincell souerce for a waist band to dectect gait and analyse a probable fall in advance and in addition...
Hi Nordic,
We are building a product in the field of Sports, specializing in running shoes. The concept is to correct running form via analyzing the foot strike of the user...
Hi DevZone,
I am currently working on an external Flash OTA update via SQSPI on the nRF54L15 DK (v0.7.0). I have already verified that SQSPI read/write operations are...
