Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
Hi,
Can you please guide me if I want to receive a larger message of around 15KB from server, how can I do it using CoAP block transfer in thread.
I am using nRF5 SDK...
Hi,
I built the nrf/samples/bluetooth/hci_lpuart program in SDK v3.1.1. I am using an nRF9160DK board version 1.1.0. I did add several printk statements to zephyr/samples...
Hi Team,
We are working on a commercial pre-production project using nRF5340 and are currently migrating from nRF Connect SDK 2.6.1 to NCS 3.1.1 . We followed the official...
I have several hardware pieces based on the Fanstel WM02C nRF7002 module (nRF54L15 host) and am having problems connecting to WiFi networks on a subset.
All modules successfully...
nRF54L15, Zephyr +MCUboot. I am unable to redirect LOG_INF() output to RTT.
prj.conf
Can you tell me what is wrong? How to force logger to output to RTT?
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
We are trying to pass interrupts at high speed (clock signal) running at 800khz from port p1 to signal the RISC-V Co-processor to trigger a capture on a 4 bit bus. Is it possible...
Hi,
using nrf connect sdk 3.11, nrf54L15-PDK
I am testing low power with development board, I am trying to reach low power 2.9uA as bench marked.
When GPIO (button)...
I noticed in SD7 SDK16.0.0 when CENTRAL and PERIPHERAL connections are defined, the soft device will return designated central and peripheral connection handles. For example...
Hi,
We are modifying our existing product and adding PA to increase the range. Device right now is developed with nrf5 SDK, but we have plans to move to NCS. However manufacturer...
hi support team,
customer is using our 54L15 for mesh lighting project, here are three questions:
1.
customer needs timer model, i see the "time_cli.c" and "time_svr...
I'm developing for a custom board that has an nRF52832 and an FM25W04 external flash. My application uses nRF Connect SDK v2.9.2. I have a debug build that doesn't use a bootloader...
Gemini gave me some code to help get the phy when a connection is updated which does compile but there is an error warning in vs code. Here is the code:
here is the error...
We are evaluating the nrf54 series chips for a new product. We currently have a product that uses the nrf52 series and the distance measurement library. I see that the nrf54...
