Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hi all,
I just got the LESC OOB example working. Currently the OOB data from the central en peripheral are exchanged, and the connection sets up flawlessly. However I would...
Hi teams,
I am trying to interface ENC28J60 ethernet controller on nRF52833 based board.
The purpose is sending/receiving simple data gathered from BLE mesh network. ...
Hi,
Can we use nrf52840 dongle as sniffer for multiple protocols?. Can we sniff non nordic devices by using this?.If not suggest me other nordic products which can use for...
Hi
i wanted to run http_application_update sample project on a local LAN. Please suggest me what all changes i have to make to sample project.
i have connected my board...
hello everyone：
I have an issue on nrf52832 running freertos based on SDk 15.0,I am using PPI and SAADC to get 2 channels data .I find that if I change the configuration...
Hi,
I have 3 estimote beacons which I want to scan using nrF52833 and display scan response data on Segger RTT viewer and I don't want to establish the connection between...
Hello,
i've made a custom shield plugged into the thingy: 52.
There is a tag connect connector on it. I have short SWD signal from thingy debug connector.
When i try...
Hey,
Is it not possible to use any Bluetooth status codes for disconnection when calling sd_ble_gap_disconnect ?
for example this is not working (I do not actually disconnect...
Hi,
Similar as this issue
Our QA team found the nRF9160 device will hang when user pull out the USIM card then try to deactivate LTE.
The issue can be repoduced by following...
We tested this issue on serial_lte_modem sample on NCS 1.2 and modem mfw_nrf9160_1.2.0
1, Enable CSCON unsolicited report:
AT+CSCON=2
2, Activate LTE search and connect...
Hi,
My problem in shortly is when I have debugger connected to nRF5282, I always get hardfault after some time.
https://i.ibb.co/hZ3bZ1b/optionbytes-1.png
I tried...
hi .i use the pca10056 connect to th nrfconnect by usb .andr dun the app Bluetooth low energy.other 52840 device run the hex of \nordic
sdk\nRF5_SDK_16.0.0_98a08e2\examples...
Hello,
I'am working with a project and want to maximize ble throughput from ble thingy52 to a central device. I have used the ble sniffer with wireshark to see data transfer...
Hi Team,
i am working on serial LTE modem sample project trying to send at commands through serial lte link monitor, found that device is not responding to at commands...
Hi,
Recently I updated nRF Toolbox iOS to 5.0.1.
I'm mainly using this tool for writing application via DFU to nRF51822 board.
I was using .hex files for DFU but I can...
