Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
I have working with Bootloader development on nrf52840 controller, for that i followed devacedemy course for firmware update using Uart and able to update firmware using...
Hi,
I get a Mcu Mgr Error: 10 Group: 1, when I
start OTA on Android smart phone
interrupt during upload by disabling BLE on the phone
enable BLE again
retry OTA...
Hello,
I was using VS Code earlier today creating different build configurations for our hardware (nrf52840 and nrf9160 based) and everything was fine. I restarted the application...
I am currently using two nRF52840s to create a transmitter, one that acquires data and transmits it as advertisement data, and a receiver that receives data from the advertisement...
We are using nRF52833 with Softdevice S113 for BLE.
in the OS_Idle function, nrf_pwr_mgmt_run is called.
But never comes out of sleep.
Is there a need to call nrf_drv_power_sleepevt_init...
Good morning,
I am developing a RAK4631 (Nordic nRF52840 + Semtech LoRa SX1262) and now I need to manage the power consumption. My environment today is a VSCode/PlatformIO...
i am working with nrf52840 with nrf5-sdk 17.1.0 and with segger embedded studio 5.42a i am having trouble build a project and it is giving below warnings: Building 'main_app...
Hi,
I am trying to test the ICM42670 sensor using nRF9160 with Zephyr V2.6.0 and I am getting an errors when I init the sensor:
unexpected RESET_DONE_INT value, 0
ICM42670...
I’m using the nRF52832 with SDK 14.2.0 and would like to implement AES-128 CCM. Could you provide relevant documentation or instructions on how to achieve this?
I was developing my development kit with onboard sensors and other ICs. So, I was looking into NRF52 DK schematics and documentation. the problem is that the interface/debugger...
Hi,
I want to use the onboard 5340-DK QPSI flash for saving binary data into, however when i enable the support for it i get that the device is not ready. I have tried both...
The above is my code.
This is running log.
After scanning multiple times, my application may freeze, as shown in the log, and there will be no response after receiving...
I am developing a project on nRF9161.
I am interested in calculating data usage for different protocols (for example MQTT with TLS) when communicating with a server over...
Hi,
I refer to the method of the link below, which can generate factory_data.hex
https://docs.nordicsemi.com/bundle/ncs-latest/page/matter/nrfconnect_factory_data_configuration...
