Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I am on NCS 2.9.0, I have tested lesson 5 exercice from NRF Intermediate course about BLE DFU, I have some questions about it:
- with mcumger, is there a way to update...
Hello,
We have a custom board we are developing on that uses the nRF54L15 MCU. The board has some LEDs that we were hoping to drive using PWM, but these are connected to...
Hi all
I have some trouble with a new batch of nRF9151 chips.
The old one had the Firmware: 2.0.2
The new ons have the Fimrware 2.3.5.
My application does no longer...
Hello
I tried to test OTA function with smp_svr example.
I want to use the external flash mx25r64 on nrf54l15-dk(v0.9.3) to store update Firmware over BLE. SDK version...
Hello,
I have some unclarities for the APPROTECT mechanism on NRF9151.
Basically, I had a misunderstanding of the involved CONFIG features, and as a result I used CONFIG_NRF_APPROTECT_LOCK...
Hello,
I’m using an external NFC reader/controller (NXP PN7160A1HN/C100E) connected via I2C to an nRF52840 module (Raytac MDBT50Q-1MV2) on a custom PCB. (Programming is...
On nRF52840, after power up, I continue to randomly get hangs. I am having trouble figuring it out, but it seems every time I encounter the issue, it is related to RNG. If...
We are designing BLE products based on the Nordic nRF52840 chipset and star network topology which are used indoors, according to the network structure, we use one Master...
For our application we are using the nRF9160 and we need low re connection / reset timeouts. Sometimes during a bad chain of events our application will trigger the reset...
Hello, I'm current using the nRF9151 DK, modem firmware version 2.0.2, sdk version 3.1.1.
I built my application on top of lessons 8 and 4 in the Cellular IoT Fundamentals...
Using Zephyr in NCS 2.8 on nrf5340/nrf7002 wifi combo, and trying to get https to work. I'm using the option where the TLS setup is done in the socket layer (enabled in prj...
Hi,
This was a major nuisance for me. As you know from the nRF52832 product spec, the TWI interface is deprecated in favor of TWIM. You may also know that there are any...
I am using the Scanning module in NRF5 SDK v17.1.x to set up a BLE scanner that matches a specific name e.g. 'NordicSemi'. The above string contains 10 characters ( But the...
Hi,
What would be the state of SWD/SWCLK be when the nRF52840 is held in RESET mode?
I am thinking if a simple gang programming be implemented by SWD/SWCLK be shared among...
