I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
This is a new install of NCS 6.1. Installed using nRF Connect Desktop v3.7.0 Toolchain Manager and connected to a new nRF5340 DK.
I followed the Getting Started, Running...
HI Nordic,
I am working PCA10040, SDK17.0.2, ble_app_uart routine.
I'm try to add ADV/SCAN_RSP data, but when I add some field, such as p_manuf_specific_data or service_data_count...
nrf52840 nrf5_sdk 16.
Looking to use the LPCOMP to wake the nrf from System OFF.
Question: if I config the LPCOMP to use the internal reference "15-level internal reference...
Excuse me:
Suppose I Initialize and turn on UART and the power consumption is 4mA，When I call app_uart_close() the power consumption is 2mA,If I don't initialize UART at...
Hi all,
I have been trying to work with UARTE for both TX and RX, and my test code is working with RX perfectly but not TX, when i try to transmit my data using uart_tx...
Hi，
I am doing a micphone " sph0641lm4h-1 ", and I use api of nrf_drv_pdm .c,
when I read mic data from sph0641lm4h-1 , they are just sets of 16 bit data, the following...
Hi. Thank you for your interest in my writing. I'm working on the IOS and the Multiple Connection project at the experimental_ble_app_multiperial example. It's a project that...
Hello,
I have been using the TWIM peripheral of the nRF52832 (via the twi_mngr) to talk to an accelerometer and a magnetometer. I have 4.7k ohm pullup resistors (in parallel...
Hi,
I am using nrf52840 customized dongle in our project. We have interfaced ADS1118 using spi communication with nrf52840 (customized dongle). The problem here with the...
I am trying to build the 'BLE NFC pairing reference' example for nRF52840.
I downloaded the latest SDK and located this example in the experimental directory under BLE\Peripherals...
nRF52840
SDK 15.3
Segger Embedded Studio
I PWM a piezo buzzer (with a transistor) , using the PWM peripheral. The problem I encounter is that before I call the PWM...
hi support team,
i have a wired problem that i can't explain to customer:
first, i test this project "nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_keyboard...
I was able to successfully use the example ble peripheral blinky firmware example with the blinky mobile app. I added peer manager for passkey pairing but the blinky app is...
Hi Nordic Team,
I am using ble_advertising_advdata_update() to update some of the advertising data. I am doing every time the device is asked to advertise. In my code I...
the following report map is working when i try to increase volume on windows system (send 1 byte == 0xe9)
0x05, 0x0c, // USAGE_PAGE (Consumer Devices) 0x09, 0x01, // USAGE...
