Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
On nRF54L15 (NCS v3.1.0), we are using the SAADC with ADC_GAIN_1_4 and ADC_REF_INTERNAL at 14-bit resolution to measure an analog voltage on AIN5. The driver sets ref_internal...
Hi.
I am attempting to obtain SIG certification.
I am using ncs v3.1.1 with nRF52833.
Based on the link below,
https://docs.nordicsemi.com/bundle/comp_matrix_nrf52833...
Dear NORDIC engineers, excuse me. I would like to inquire about the Settings of NRF54LM20 APPPROTECT. I have modified APPROTECT[n].protect0 and APPROTECT[n].protect1 to 0x5A5A5A5A...
I am trying to use the nRF54L15 DK board to flash a Fanstel BM15M module.
Fanstel BM15M module link: Fanstel BM15M Module
I am using the nRF54L15 DK board with the external...
Hi --
We are in the process of setting up to flash a few hundred devices for our internal testing. We can currently flash to our board using nrfjprog either directly from...
I have a nRF9151 dev kit for evaluation that I am following official guide to get up and running using the asset tracker v2 program. I can flash the firmware but I cannot...
I want to expand the flash allocated to mcuboot on the NRF desktop, but it failed to start after compilation
The following is a flash layout that can be successfully launched...
It seems there might be a small issue with the TF-M GPIO MCU-select IOCTL plumbing on nRF54L — specifically when a non-secure app tries to configure sQSPI GPIOs (and presumably...
I have successfully completed the one script install of Zephyr on RPI and can fully develop Nordic nrf52832/nrf52840. I assume all other supported boards within Zephyr can...
I'm trying to advertise an isochronous IN endpoint with wMaxPacketSize = 768 bytes (8 channels × 48 kHz × 16-bit audio, 1 ms polling). USB init fails at usbd_init with Failed...
Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
I measured the power consumption of the BLE RX using the nRF54L15.(nRF54L15-DK v1.0.0) 3.0V operation apps: scan_adv (delete advertising) west build -b nrf54l15dk/nrf54l15...
Hi Nordic Team,
I’d like to ask: Does the recommended Bluetooth matching circuit for the nRF54L15 need to be designed as a bandpass filter?
Also, do you have the VNA...
Hi devzone, I'm working on the nRF54L05, having an application and the mcuboot generated correctly on my host computer. Now we want to generate the binaries on Bitbucket pipelines...
