Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I'm posting some thoughts in the hope of receiving some useful feedback, or at least bringing together information that is currently scattered a bit all over the place on...
Hi Nordic,
We currently put cpu in deep sleep when battery charging almost finished.
We are using DMA (TWIM, SPIM), Timers (1-4) and PWM.
We explicitly turning...
Hi! I am developing project based on nrf9160 as a main processor and nrf52840 as a hci controller. I am using nrf connect sdk 2.6.1. I came across a potential issue in nrf...
Hi,
I'm trying to implement firmware updates over BLE with mcuboot as boot loader.
I got it working with NCS 2.6.1, but I've upgraded to NCS 2.8.0 and now nRF Connect...
Hello,
I am working on the GNSS application provided in the sdk-nrf at [path: samples/cellular/gnss] and I'm using thing91: nrf9160 board. I have modified the GPS acquisition...
Hey, I try to implement wtih nordic connect sdk and the nrfx library a uart communication where a 9th data bit will send for synchronisation. When the 9th data bit will be...
Hi,
I have an NRF5340 application based on zephyr which produces a combined merged_domains.hex file.
I need to add a post build command after the "merge_domains.hex...
Dear Nordic
Q1.
We tried new nrf9151 IC at custom board.
IC version: nrf9151 AEA (Engineering B)
Firmware: ncs2.7.0 Serial LTE modem application + mfw_nrf91x1_2.0...
hi,
When verifying the modem upgrade, if the network type is set to support both Cat-M and NB (AT%XSYSTEMMODE=1,1,0,0), the actual network that connects is NB, and the modem...
I have 3 nrf boards connected. 2x nrf52832 and 1x nrf5340.
esb_tx is running on nrf52832(682782977) esb_rx is running on nrf52832(682497942) & nrf5340(1050025410)
west...
Hello
I have a custom nrf52840 board with an external 1MB NOR flash
The app uses MCUboot for DFU
I know I can define the external flash in the pm_static.yml for the...
We are currently working with the nRF52832 Development Kit and are aiming to interface an ISO15693 NFC reader using the PN7150 NFC module. We intend to communicate with the...
Are there any serial commands that I can use to control some the functionalities of the board. My task is to use the dk with a windows app (UWP, C#), I want to start stop...
