Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I have achieved bluetooth direction finding using nRF52833DK. I would like to do the same with a custom board. I have used the BM833 chip for doing this. I have attached the...
Dear Nordic,
We made an attempt to use the external flash in the LwM2M sample.
We tried to follow this: docs.nordicsemi.com/.../nrf9160_external_flash.html
As soon as...
Hi.
When working with certain nRF connect SDK versions 2.x.x (not sure which range) in visual studio code, the build terminal outputs relative file paths when showing warnings...
I am looking for some simple slave and master samples to run on my dk's nut cant find any. in the intermediate course there is the master slave talking with the sensor but...
When will the nRF9151 Hardware Design Guidelines document be available?
We are currently leveraging information in the nRF9161 Hardware Design Guidelines document in the...
I am building a nrf52840 custom board and testing the ble_app_blink_pca10056_s140 example from segger I have a 32MHz crystal and a 32.768khz crystal And I added the following...
I've got a custom board using an nRF52832. I'm using the P0.06/P0.08 as the TX/RX pins for UART comms, but don't need the P0.05/P0.07 pins for CTS/RTS. Is there anyway I can...
Hello. I am currently working on a Mesh Network using the Nordic Thingy53 board. As far as I understand, the Mesh protocol developed by Nordic already has encryption, obfuscation...
Hello,
In a project using the NRF52832. Softdevice SDK 19.1.0 and Segger IDE, I inizialize the BLE for having NUS and DFU services actives. I try to reproduce the code here...
Hi,
I would like to ask when using zephyr's k_timer it uses a clock from LFCLK, then it can be generated in the following three ways:
32.768 kHz RC oscillator (LFRC) 32...
Hello Team NordicSemi Q&A,
I am beginer in Nordic Semiconductor Device. My question is related of nPM1300 Quiescent Current. In datasheet for Sleep Mode and Hibernate Mode...
Hi. i am trying to turn ON a LED1 and read its status and then turn ON LED2 based on status of LED1 in nrf52840dk board.
#define led1 28 #define led2 25 #define Button 12...
These seems like another dumb question. First off, I am aware that the nrf21540DK is the nrf52840 with the FEM tacked on the output.
I know I can select the nrf21530DK/nrf52840...
Hi,
I’m experimenting with the nrf9160 LTE modem in poor network conditions. I would like to be able to keep track of how long the modem spends searching for LTE networks...
Hello,
I'm having an issue with performing fw update with ble mesh DFU examples.
My setup is pca10056 used as distributor and pca10059 - dongle as target.
I'm using...
