Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi, there
I am using nrf52832 chip on a custom hardware and also using softdevice 132 to send data to an app.
I need to send data from app to MCU and vice-versa and...
Hi
I am using the nRF52832DK and the BLE_App_Blinky.
I have a stable BLE connection to a phone and then I try to close the connection inside the nRF with sd_ble_gap_disconnect...
Hi, I am trying to implement Azure FOTA using your libraries. My source code is a combination of the Azure iot sample and the Azure fota sample + some necessary alterations...
As I know,the New Order Code of nRF52 Series has added Access port protection Controlled by hardware and software function, the earlier order code : Access port protection...
Hi, I'm working on updating nRF9160 modem firmware update.
I have update modem[mfw_nrf9160_1.3.1.zip] using nRF connect Desktop application and read partition using nRF...
Hi
I run nRF connect SDK 1.7.1 and have a custom nRF9160 board.
I'm trying to get the I2C peripheral to work with my own hardware.
I have read and googled all tutorials...
Hi,
Can I use the hex file compiled for nRF52810 for nRF52805 directly ? Please note that I am not using any peripherals other than radio.
Can I use the nRF52810 build...
We use the nRF24L01+ in a dedicated RX mode, and it is preceded by a power splitter, filters and LNA. In order to run some system calculations, I'd really like to know the...
We are using nRF52840 on a custom board with nRF5 SDK v15.3.0.
Our application uses the NFCT driver (nrfx_nfct) along with nfc_t2t_lib_gcc.a to emulate a NFC tag with some...
HI,Therd:
I used the mesh sdk 5.0.0(BLE SDK 17.0.2), and run the example light_switch_server_nrf52832_xxAA_s132_7_2_0.emProject. when i use the nRF Mesh app on the phone...
Hi,
I am evaluating nRF53 for ZigBee in a Linux application that implements a MQTT-SN Gateway. I am interested in learning about Linux board can connect to the nRF53 (USB...
using nRF5 SDK 17.1.0
Segger
I need some understanding of the QDEC. if I connect a motor that has a A/B output at a 5KHZ rate.
what is the maximum rate at which the...
Hi,
We are trying to change the name of our BLE device of our solution with being always different for each device. The device name would be like a serial number that is...
SDK: 7.0.2
CHIP: nRF52840
I'm faced with strange dfu behavior.
The dfu SD+BL+APP (softdevice 6.1.1 -> 7.2.0) is working fine which was flashed by j-link.
However...
