Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Why is the pc-ble-driver-py version 0.16.2 released to pypi , but no according tag and release set in the github repository?
Is this a stable release already? And if so...
Hi
Problem description：
Disable the softdevice before writing uicr. After uicr is written, it fails to enable the softdevice again.
Can't softdevice be enabled again...
Hi I want to Integrate GPS(with A GPS assistance needed)with AWS iot example. when i start GPS on aws connect event ready .SUPL is initialized successfully and even SUPL socket...
Dear Nordic,
I'm using the nRF connect app for the smart phone to test BLE bonding.
I hope to know the bonding feature on the nRF connect app is working with Random...
Hi.
We've created a custom board, and it works nicely.
However, when I try to build another application for this new board (i.e. "Add Build Configuration"), the new board...
Hi,
I'm using the nRF Connect app on android to DFU my devices.
On some occasions, after doing DFU and unbonding, the phone will keep asking if I want to pair the device...
The Absolute Maximum rating of I/O pin voltage for VI/O, VDD ≤3.6 V is -0.3V to VDD + 0.3V in Table 185. We would like to monitor the battery voltage using an AIN pin because...
Hi, We are using the SDK v17.1.0 and SD S140 v7.2.0. In our application we have to send only 1 advertising packet with updated data every 300ms and in some cases every 50ms...
Hi,
I work with win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk.
I modifyed peripheral_uart to use 240 bytes like it's explain into "ncs 1.6.1 peripheral_uart...
Hi, I am trying to create a custom BLE service.
Following is the main code:
These are my BLE write functions:
My sdk_config file says MAX_MTU is defined 23
...
Hello everyone,
I have a few questions related to NFC in nrf52832.
1. UUID in nrf52832 NFC is Unique?
2. Can I use nrf52832 NFC for payment purposes..? if yes How I...
Hello sir,
I am using nrf52832 soc with customised board want to use as UART pins as RX pins as 23 and TX pins as 24 .Is it possible to use the RX pins as 23 and Tx pins...
Hello,
I am trying to configure a Zigbee coordinator as done in the CLI example (for example 'bdb role zc' and 'bdb start') to get data from the multi sensor example,...
Hello,
Lately we've had some problems with DFU using the NRF connect app.
The device we are using is a nrf52832 running Zephyr 2.6 with MCUBoot 1.8
When we set the following...
