Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
My project builds when set to Release, but fails when set to Debug. Here are the last few lines of the transcript output:
1> "C:/Program Files/SEGGER/SEGGER Embedded Studio...
I'm looking to store a batch of data in a large array in RAM and send them all at once later. I start from ble_app_template in sdk examples and add an array. My memory setting...
I'm trying to get LPCOMP working on Zephyr - I have used the vanilla NCS sample as a baseline and have set up the event handler and the init function.
The problem is that...
Hi,
I recently bought a couple of HolyIOT nRF52840 modules for a personal project (building a keyboard). I also got a JLink Edu Mini to flash/debug it. I am able to successfully...
Hello,
I've seen when ADV interval is near than 1 second, the sniffer cacth the same adv twice in diferent channels, but if the adv interval is near to 50 ms the sniffer...
Dear all,
I managed to implement custom firmware using Nordic proprietary protocol (both 1 and 2 MBPS) on nNRF-52840-DK. I would like to know if some spread spectrum tecnique...
A plain question : we are using the BLE stack with FreeRTOS based observers.
Is it possible to send to some observer an application defined event from some other FreeRTOS...
My project is a health thermometer using nRF52833. I am working nRF5 SDK 17.0.2 with GCC make complier.
I start with the ble_app_hts example and it is working fine. I try...
Hi,
I observed that in some cases SLM waking up from idle mode (at#xsleep=0) has CFUN reset to zero, even if I run AT+CFUN=1 before at#xsleep. Presumably that happens when...
My current implementation is based on light switch example and I am currently using nrf52832 kit with Mesh SDK v5.0.0. I have a mesh network setup with a client and two server...
Hello,
I am using nRF52833, nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 and SEGGER Embedded Studio for ARM 5.34.
I have imported some multiprotocol examples and trying...
I have an nRF 52832 running the SDK 15.2 with s132_nrf52_6.1.0_softdevice as peripheral and a Dell XPS 13 9350 laptop with the integrated bluetooth 4.1 module (Dell Wireless...
Hi,
can you please tell me in what cases I get this assertion?
SOFTDEVICE: ASSERTION FAILED, PCxxx: 0x12D7E
It seems to happen when a connection is active, timeslot...
HI All team Members !
Hope you all doing well ! . Yesterday , i have tested the two SDK's "ble_app_uart_c" as a BLE Beacons Scanner and "ble_app_beacon" as a BLE Beacon...
