Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
I am following then nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using nRF Connect SDK 1.4.99-dev (installed via the Toolchain Manager)
In part 1.3.2 Build...
I recently switched from 52832 development using IAR to 52833 development using SES. As a result, I downloaded all new versions of the SDK, softdevice and, of course, SES...
There is a marked improvement in the handling of TrustZone in nrfjprog 10.11.0 and 10.12.00, but it seems it's still not quite all the way there. I can do:
and am able...
Hello,
I am developing DFU over a custom IEEE802.15.4 Protocol in our own embedded OS. I managed to write the new Firmware starting at bank1_start address. Now I need to...
Hello,
I am using nRF connect SDK v1.4.99-dev1. I have imported ZigBee light_bulb, light_switch,network_coordinator project in SEGGER and successfully created
the Zigbee...
-I was following this link- " devzone.nordicsemi.com/.../" and installed SEGGER JLink.
(all on Ubuntu)
-Installed gcc-arm and changed the tool chain path on Makefile.posix...
I try DTM using the serialized application . The serialized application interface is UART.
The software on Connectivity board is ble_connectivity in nRF5 SDK , it is not...
nRF52832 and SDK 17.0.2
Using the Examples/crypto/nrf_crypto/aes/aes_all_cli example I am getting the wrong output in CFB mode.
"example key_size 256_bit"
"example aes...
I am working on nRF51-DK with nRF51422 with softdevice S130 and SDK 12.3.0.
I see that GPIOTE driver provides sensing for signal transitions like NRF_GPIOTE_POLARITY_LOTOHI...
Hi,
I have setup the Segger Embedded Studio for ARM (Nordic Edition) V5.10d, and managed to compile a sample app from ,
V1.4.2 -> nrf -> samples -> bluetooth -> peripheral...
Hello,
I have different behaviour with 2 identical boards.
They behave differently (at least for BLE functions).
With jlink interface, I saved the flash binary of...
I have installed the toolchain according to nRF Connect guideline, on my MAC OSX.
My option settings are listed in the attached image.
I downloaded release 1.4.2.
...
Hi Sir
We are developing a product with nRF5340,
Now we faced the PCB layout symbol creation issue,
I can't find any information about footprint of nRF5340,
Can someone...
Hello,
I am trying to get acquire the accelerometer data every 4 hours for a sample duration of 60secs. These data are stored in RAM and on ble connection with the mobile...
Hi,
I'm totally new to programming nRF DK's.
What am I using?
Segger Embbedded Studio for ARM (Nordic Edition)
Toolchain: nRF Connect SDK v1.4.99-dev1
The "mqtt...
