Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello there,
Since we use the lower level modules from Nordic's SDK for Mesh 4.2.0 - namely timeslot.c, bearer_handler.c and some additional modules to make them work properly...
Hi,
I just happened to stumble across these lines (123 to 126) in nrf_drv_uart.h:
And I noticed that on line 125 NRF_UART_ERROR_FRAMING_MASK is mapped to NRF_UARTE_ERROR_PARITY_MASK...
Hi, I've got our custom board with W25M02GVZEIG and I want to be able to read it out in a way that is fast and works with XIP. It's ok if it takes more time to write.
So...
Hi, I've made UART (BAUD RATE 1M) only on central after recieve all data (8kB). Peripheral is sending data from own ram (collected data from SPI sensors). What and how i need...
Hi,
I am trying to start from scratch BLE firmware to send and receive data from the development kit PCA10100 and nRFConnect App. I am following this course on Github here...
Hi,
i am trying to send temperature data along with timestamp as a string over BLE to a smartphone. i did the temperature reading part and now want to add timestamps to...
Can you show how can I merge the ble_app_uart and ble_app_uart_c into one code?
Once the device wakes up, it will check its GPIO - if it is '0', the peripheral will start...
Hello,
this is my second question in this forum, again regarding floats. (I hope its not something obvious like last time)
I`m getting very different results from asinf...
Hi,
I am following then nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using nRF Connect SDK 1.4.99-dev.
When trying to create the hello_world project i get the...
Hi,
I am current working with nrf connect SDK, nrf5340dk and 2 Nordic thingy 52s. I am trying to implement BLE mesh sensor client and server model on both the Thingys respectively...
Hi,
I want to merge provisioner and client to provision, configure and control multiple servers from the provisioner+client module.
SDK = nRF MESH SDK v4.2.0
Example...
Hey guys,
All of a sudden, I'm not able to flash my nRF board anymore. I get the following message when I try to connect to the board using segger IDE.
And when I try...
Hello,
I had purchased 6 nRF52840 Preview Development Kit boards in 2017 for study and development.
This year, I want to re-use the PDKs for a new BLE-THREAD related PoC...
